Results 61 to 70 of about 1,137 (212)
The evolution of the temperature field and frozen wall under different fracture conditions was examined by an artificial ground freezing‐based thermal‐hydraulic coupled model. It was observed that fracture inclination affects the interaction extent of freezing pipes and fracture, while phase transition extent is the dominant factor for heat transfer in
Chenyi Zhang +9 more
wiley +1 more source
International Tables for Crystallography is the definitive resource and reference work for crystallography and structural science.
Each of the eight volumes in the series contains articles and tables of data relevant to crystallographic research and to applications of crystallographic methods in all sciences concerned with the ...
Gerrit van der Laan C. Chantler +2 more
wiley +2 more sources
This review elucidates the velocity–dispersion–attenuation coupling mechanisms of wave propagation in rock masses, compares six representative models, and reveals how pressure, temperature, mineral composition, and anisotropy jointly control dynamic responses in complex geological media.
Jiajun Shu +8 more
wiley +1 more source
Seismic analysis and design of tunnels within fault ground: A review
The research methods of seismic response of tunnels within fault ground, including field investigations, analytical solutions, physical experiments, and numerical simulations, and seismic countermeasures are discussed. The present study examines the shortcomings and limitations of the current research and design, and puts forward proposals for future ...
Xingda Wang +6 more
wiley +1 more source
Investigation on tunnel stability considering pipe‐roof support with transparent soil technology
This study integrates transparent soil technology, 3D reconstruction and numerical simulation to captures the full‐field deformation of shield tunnel instability. Results demonstrate that pipe‐roof support enhances stability via the “soil‐arching barrier effect,” effectively restraining failure wedge development by extending stress transfer paths ...
Zhi Jia +4 more
wiley +1 more source
Lithium Metal Anode Fabrication: Methods, Challenges, and Strategies
Schematic illustration of four representative fabrication techniques for thin lithium metal anodes: extrusion, molten lithium infusion, electroplating, and physical vapor deposition (PVD). ABSTRACT The pursuit of ultra‐high energy‐dense lithium‐metal batteries (LMBs) has reignited the drive to fabricate ultrathin high‐quality lithium metal anodes. This
Ji Hyun Baek, Mi Ji Kang, Ho Won Jang
wiley +1 more source
A one‐step gas‐phase synthesis directly assembles amorphous Si nanoparticles with few‐layer graphene heterostructures via in‐flight mixing. Compositions with only 15 wt.% FLG deliver ~2800 mAh g−1 (Si + FLG) at 0.05 C and retain ~1400 mAh g−1 after 100 cycles at a high cycling rate of 1 C, enabled by a percolated, strain‐buffering graphene network that
Muhammad Ali +5 more
wiley +1 more source
Finite Element Analysis for Li Batteries at the Mesoscale
Finite element analysis (FEA), through multi‐physics coupling, has been widely employed to calculate mesoscale structures in LIBs that exhibit inherent randomness and disorder (Figure a). It has been extensively applied to the investigation of critical phenomena such as Li dendrite evolution, Li+ concentration gradients, SEI film growth, particle ...
Guanwu Li +3 more
wiley +1 more source
Light‐Modulated Exchange Bias in Multiferroic Heterostructures
In this article, exchange bias and magnetization are modulated with visible light at room temperature in PMN‐PZT/FeGa/IrMn multiferroic heterostructures. Photostrictive effect is the main mechanism leading to the modulation of magnetic anisotropy and interfacial exchange bias coupling between the ferromagnetic and antiferromagnetic layers.
Huan Tan +9 more
wiley +1 more source
ABSTRACT This study addresses the influence of fibre architecture on the mechanical properties of vacuum‐infused glass fibre reinforced polymer (GFRP) composites at elevated temperatures (ET). Laminates with three different fibre configurations—unidirectional (UD), bidirectional 0°/90° cross‐ply (BD), and ±45° off‐axis angle‐ply (OA) – were tested in ...
Eloísa Castilho +4 more
wiley +1 more source

