Results 51 to 60 of about 59,765 (181)
Effect of velocity on roll/slip for low and high load conditions in polymer composite [PDF]
, 2011 In the last decade polymer composites are often used without lubrication on both low and high speed applications. Some of the application areas are marine, automotive and agriculture used as bearings and cams where roll-slip is the dominant mechanism ...
Andó, MátyásUGent80200081473500009143321027C92CA2-F0EE-11E1-A9DE-61C894A0A6B4 +4 more
core +1 more source
Polymer Composites, EarlyView.Materials used for fabricating sustainable composites. ABSTRACT A composite sample with 18% flax fiber flyash (FF) exhibits increased tensile strength (TS) and greater load‐transfer efficiency of the reinforcement under corrosive conditions.
Sumesh Keerthiveettil Ramakrishnan +2 more
wiley +1 more source
Effect of Surface Texturing on Friction and Film Thickness under Starved Lubrication Conditions [PDF]
, 2015 Tato disertační práce se zabývá vlivem mělkých mikro-textur na tření a tloušťku filmu v mazaných nekonformních kontaktech za extrémních podmínek a za podmínek hladovění kontaktu. Měření byla realizována na tribometru v konfiguraci ball-on-disk.
Ali, Fadi
core
Polymer Engineering &Science, EarlyView.This review integrates the molecular fundamentals, key challenges, and mitigation strategies in polyolefin 3D printing, focusing on shrinkage, warpage, and adhesion control. It highlights material design approaches using recycled polyolefins and functional fillers to improve printability, mechanical properties, and sustainability in additive ...
Malik Hassan +5 more
wiley +1 more source
Polymer International, EarlyView.Fullerene particles were incorporated with CF‐reinforced acrylonitrile–butadiene–styrene terpolymer (ABS) matrix at three different compositions by a melt‐compounding process. These insights are crucial for the optimization of conductive hybrid composites for various applications.
Alinda Öyku Akar +4 more
wiley +1 more source
Dental composites: a comprehensive review on formulation, properties and recent developments
Polymer International, EarlyView.Dental composites are essential in modern restorative dentistry; this review covers their development, composition, key properties and recent advances, highlighting new technologies for optimizing materials and improving clinical outcomes. Abstract Dental composites have evolved considerably since their introduction, becoming the cornerstone of modern ...
Rayenne Latoui +2 more
wiley +1 more source
Some aspects of oil lubricant additivation with ZnO nanoparticles [PDF]
, 2006 This is a study on the tribological behaviour of ZnO nanoparticles as an additive in a polyalphaolefin (PAO6) and on the influence of dispersing agents (OL100 and OL300). Antiwear and extreme pressure tests were run on two four-ball machines. Firstly, it
Chou, R. +4 more
core
Auger Parameter Analysis for TiN and AlN Thin Films via Combined In Situ XPS and HAXPES
Surface and Interface Analysis, EarlyView.ABSTRACT Auger parameter analysis provides in‐depth information about electronic and chemical bonding properties of TiN and AlN thin films, which are relevant across a wide range of technologies. Meaningful interpretation and analysis of Auger parameter of these materials have been hindered due to, among other reasons, the absence of reliable ...
O. V. Pshyk +3 more
wiley +1 more source
SmartBot, EarlyView.Tendon‐sheath mechanisms are widely used in various robotic systems for remote position transmission, including aerospace vehicles, flexible rescue robots, dexterous robotic hands, exoskeleton robots, soft wearable devices, industrial robots, and flexible surgical robots.
Jiaqi Li, Qian Gao
wiley +1 more source
Tribological behavior of composite-steel on rolling/sliding contacts for various loads [PDF]
, 2011 Composites have replaced metals in the bearing industry for the exclusive performances from its properties were it can accommodate resins, fabrics and additives.
Andó, Mátyás, Sukumaran, Jacob
core