Results 221 to 230 of about 3,019,050 (308)

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann, Berend Denkena, Hilke Petersen, Florian Schaper   +3 more
wiley   +1 more source

Research on Texture Variation Mechanism of Ti-3Al-2.5V Titanium Alloy Tube During Cold-Rolling Process. [PDF]

Materials (Basel)
Ge H, Luo Y, Wang B, Song X, Ye W, Yu Y, Li Y, Hui S.   +7 more
europepmc   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

A novel assisted technique for difficult 24-hour esophageal pH-impedance probe placement. [PDF]

Endoscopy
Yalaka RR, Mogili KR, Chennamadhavuni A, Madhuri SR, Menneni MR.   +4 more
europepmc   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

A Simplified Technique for Glaucoma Drainage Device Ciliary Sulcus Implantation. [PDF]

Cureus
Alsafi Z, Hamid S, Kandola H, Elkarmouty A.   +3 more
europepmc   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Letter to the Editor Coccolini F, Cremonini C, Moore EE, Civil I, Balogh Z, Leppaniemi A, Horer T, Reva V, Ball C, Kirkpatrick AW, Colli A. Thoracic trauma WSES-AAST guidelines. World Journal of Emergency Surgery. 2025 Oct 15;20(1):78. [PDF]

World J Emerg Surg
Kesgin YM.
europepmc   +1 more source