Tube wall thickness isotope production tubes [PDF]
, 1963 Irradiation of process tubes containing appropriate parent materials has been proposed by Manufacturing as a method for obtaining new products from the Hanford Reactors. The process tubes would be removed at appropriate intervals and shipped to separations plants for recovery of the products. The tube residence in the reactor could be determined by the
Young, J. R.
openaire +3 more sources
Concrete-Filled Prefabricated Cementitious Composite Tube (CFPCCT) under Axial Compression: Effect of Tube Wall Thickness. [PDF]
Materials (Basel), 2022 Research on different prefabricated cementitious composites for constructing composite concrete columns is comparatively more limited than that of concrete filled steel tube columns.
Kai B, Kaish ABMA, Nordin N.
europepmc +2 more sources
Total temperature measurements of laminar gas flow at micro-tube outlet: Cooled from the wall [PDF]
, 2011 This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece.
Asako, Y +5 more
core +6 more sources
Flow boiling in a 1.1mm tube with R134a: Experimental results and comparison with model [PDF]
, 2007 A detailed comparison of the three-zone evaporation model, proposed by Thome et al. (2004), with experimental heat transfer results of two stainless steel tubes of internal diameter 4.26 mm and 2.01 mm using R134a fluid was presented by Shiferaw et al ...
Karayiannis, TG +2 more
core +6 more sources
Forced-convection condensation heat-transfer on horizontal integral-fin tubes including effects of liquid retention [PDF]
, 2011 PhDAccurate and repeatable heat-transfer data are reported for forced-convection filmwise condensation of steam and ethylene glycol flowing vertically downward over two single, horizontal instrumented integral-fin tubes and one plain tube. Vapour-side,
FITZGERALD, Claire Louise
core +4 more sources
STUDY OF ALUMINUM TUBE COLD NOSING PROCESS INTO CONICAL AND HEMI-SPHERICAL DIES WITH DIFFERENT COEFFICIENTS OF FRICTION [PDF]
Journal of the Egyptian Society of Tribology, 2020 Theoretical analysis and finite element method were used to simulate the cold nosing process of commercial purity Aluminum tubes into conical and hemispherical dies.
A. Badran +3 more
doaj +1 more source
Investigation of the Geometry of Metal Tube Walls after Necking in Uniaxial Tension
Metals, 2017 : In order to characterize the deformation and true stress–strain relation of metal tubes, the geometry of tube walls after necking in uniaxial tension need to be determined. The paper investigated the necking process of metal tube.
Chong Li +3 more
doaj +1 more source
A STUDY ON MICRO BUBBLES AERATION METHOD ON WATER TURBIDITY AT AQUACULTURE EARTHEN PONDS UNDER DIFFERENT OPERATIONAL PARAMETERS [PDF]
Scientific Papers Series : Management, Economic Engineering in Agriculture and Rural Development, 2022 The experiment was established at an earthen aquaculture private farm in Kafrelshikh Government, Egypt. During 2021. To study the effect of operational variables at tube diffusion aeration system on turbidity values corresponding to Secchi disk clarity ...
Tarek FOUDA +2 more
doaj
Experimental Study on Self-Compacting Concrete-Filled Thin-Walled Steel Tube Columns
Buildings, 2022 Concrete-filled steel tubes present excellent structural and constructional performances because they ideally combine the advantage of concrete and steel tube. Thus, they are widely used in civil infrastructures.
Yunyang Wang +3 more
doaj +1 more source
USING RUBBER TUBES TO GENERATE MICRO BUBBLES FOR AERATION SYSTEM IN SEMI-INTENSIVE FISH FARMING [PDF]
Scientific Papers Series : Management, Economic Engineering in Agriculture and Rural Development, 2022 The expansion of aquaculture ponds necessitates the development of aeration and the addition of oxygen. Rubber tubes are a new way of aerating by generating micro bubbles on the water surface.
Tarek FOUDA +3 more
doaj