Results 21 to 30 of about 5,265 (262)
Recent Developments in the Aerodynamic Heat Transfer and Cooling Technology of Gas Turbines Endwalls
Aerospace, 2023 With an increased inlet gas temperature and the homogenization of the combustion chamber outlet temperature, the endwalls of gas turbines are exposed to extremely high heat loads.
Rongdi Zhang +4 more
doaj +1 more source
USING THE RESERVE OF ABSORPTION CHILLER REFRIGERATION CAPACITY FOR COOLING AIR AT THE INLET OF GTU
Авіаційно-космічна техніка та технологія, 2018 The processes of air cooling at the gas turbine unit inlet by absorption lithium-bromide chiller have been analyzed. The computer programs of firms-producers of heat exchangers were used for the gas turbine unit inlet air cooling processes simulation ...
Богдан Сергійович Портной +3 more
doaj +1 more source
Influence of Different Steam Cooling Techniques for High Pressure Turbine Blades on the Performance of Gas Turbine [PDF]
Iranica Journal of Energy and Environment, 2018 Gas turbines are always intended to give more specific work output for which continuous exposure to hot combustion gases is necessary. To increase the lifespan of the turbine blades active cooling should be applied to the High Pressure (HP) turbine ...
T. C. Vadlamudi +3 more
doaj +1 more source
Steady state design and thermal characteristics of a gas turbine blade with lateral holes using finite element analysis [PDF]
MATEC Web of ConferencesTurbine blades are the separate components that make up the turbine section of a steam or gas turbine. The blades must transform the high-temperature, high-pressure gas that the combustor produces into energy.
Sampathkumar Deepak +3 more
doaj +1 more source
Alexandria Engineering Journal, 2020 Currently, gas turbine engines play a vital role in our daily lives. Some of the uses of gas turbine engines include aircraft propulsions, helicopters, submarines, and industrial applications.
Amin Safi +2 more
doaj +1 more source
Nihon Kikai Gakkai ronbunshu, 2015 This work aims at developing a new cooling fan for vehicle engine. This fan can operate as a cooling fan at low vehicle speed. At high vehicle speed, however, the fan is rarely used as a cooling fan. Therefore the fan can be used as a wind turbine, which
Shinichi ODA +3 more
doaj +1 more source
COMPARISON OF CHARACTERISTICS OF DEEP AIR COOLING AT THE GTU INLET IN DIFFERENT CLIMAT TYPE
Авіаційно-космічна техніка та технологія, 2020 The efficiency of deep air cooling at the inlet of gas turbine units has been investigated for changed climatic conditions of operation during the month.
Микола Іванович Радченко +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm +3 more
wiley +1 more source
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Research Status and Development Trend of Rotating Internal Cooling Channel in Gas Turbine Blade
发电技术ObjectivesThe high-efficiency internal cooling technology of turbine blade is crucial for improving the thermal efficiency of gas turbine. As an important component of the gas turbine, it is essential to conduct research on the cooling performance of ...
REN Jing, LI Xueying
doaj +1 more source