Results 211 to 220 of about 1,412,477 (278)
An Inkjet‐Printed Platinum‐Based Temperature Sensing Element on Polyimide Substrates
Advanced Engineering Materials, EarlyView.An inkjet‐printed, meander‐structured, nanoparticle platinum‐based resistive temperature sensors on polyimide substrates are demonstrated as proof‐of‐concept. Optimized sintering at 250°C enables stable conductive structures. The Pt100‐ and Pt1000‐type sensors exhibit linear resistance–temperature characteristics with stable TCR in the 20°C–80°C range,
Shawon Alam +6 more
wiley +1 more source
Alterations of neocortical pyramidal neurons: turning points in the genesis of mental retardation. [PDF]
Front Pediatr, 2014 Granato A, De Giorgio A.
europepmc +1 more source
Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects
Advanced Engineering Materials, EarlyView.Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley +1 more source
Period-Based Mortality Change: Turning Points in Trends since 1950. [PDF]
Popul Dev Rev, 2014 Ouellette N, Barbieri M, Wilmoth JR.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann +2 more
wiley +1 more source
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source