Results 71 to 80 of about 984,749 (305)
Advanced Engineering Materials, EarlyView.This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani +2 more
wiley +1 more source
Possible correlation between work-hardening and fatigue-failure [PDF]
, 1969 Conceptual theory proposes that cyclic hardening due to non-uniform strain and stress amplitudes during testing, especially during the initial application of stress to a specimen, may correlate positively with the ultimate strength of the specimen under ...
Kettunen, P. O., Kocks, U. F.
core +1 more source
Advanced Engineering Materials, EarlyView.Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente +3 more
wiley +1 more source
Journal of Marine Science and EngineeringStandard structural assessments of ship hulls include the evaluation of the elastic structural response. Elastic analysis neglects extreme and unpredicted loadings, which can produce catastrophic outcomes, such as the loss of the ship’s ultimate strength.
Nikola Momčilović +4 more
doaj +1 more source
Effect of operating temperature on direct recycling aluminium chips (AA6061) in hot press forging process [PDF]
, 2013 A method of solid-state recycling aluminum alloy using hot press forging process was studied as well as the possibility of the recycled chip to be used as secondary resources.
Ahmad, Mohd Hafizi +8 more
core +1 more source
3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs
Advanced Engineering Materials, EarlyView.This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu +4 more
wiley +1 more source
Japan Architectural ReviewAccording to the “AIJ Recommendations for Design and Construction of Concrete Filled Steel Tubular Structures”, the ultimate flexural strength of concrete‐filled steel tubular (CFST) beam‐columns is calculated based on full‐plastic strength.
Ryohei Yonekura +2 more
doaj +1 more source
Zhongguo Jianchuan YanjiuObjectivesTo fully consider intact initial imperfections, including welding initial deformation and residual stress, it is necessary to conduct a study on the plastic deformation distribution and ultimate strength of a box girder under different cyclic ...
Huwei CUI, Runwen HU, Qiyin DING
doaj +1 more source
Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC
Advanced Engineering Materials, EarlyView.ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko +2 more
wiley +1 more source
An approximate method for the ultimate shear strength of horizontally curved composite plate girders
Journal of Civil Engineering and Management, 2014 The paper is concerned with the ultimate load capacity of horizontally curved composite plate girders. An approximate method to predict the ultimate shear strength of the girders is presented.
Nandivaram E. Shanmugam +2 more
doaj +1 more source