Results 51 to 60 of about 30,820 (254)

Control factor optimization for friction stir processing of AA8090/SiC surface composites

Journal of Alloys and Metallurgical Systems
Friction Stir Processing is a state-of-the-art technology for microstructure refinement, material property enhancement, and surface composites fabrication.
Karthik Adiga, Mervin A. Herbert, Shrikantha S. Rao, Arun Kumar Shettigar   +3 more
doaj   +1 more source

The Effects of Combined Chemical Treatments on the Mechanical Properties of Three Grades of Sisal

BioResources, 2016
Different grades of sisal fibres (S3, STOW, and SUG) were immersed in five different treatment solutions: sodium hydroxide (NaOH) for 24 h; silane for 24 h; and NaOH followed by silane for 6, 12, and 24 h.
Sameer Adnan Ibraheem, Subramania Sarma Sreenivasan, Khalina Abdan, Shamsuddin A. Sulaiman, Aidy Ali, Dayang Laila Abang Abdul Majid   +5 more
doaj   +1 more source

Cellular Responses to Mechanical Cues Across Scales: From Fundamental Insights to Translational Potential

Advanced Healthcare Materials, EarlyView.
This review examines how cellular behavior is regulated by mechanical cues transmitted through soft biomaterials, from single‐cell mechanosensing to tissue‐level adaptation. It highlights why physiological relevance, rather than model complexity alone, is critical for translational mechanobiology and introduces a scoring framework linking material ...
Mathias Polz, Manuel P. Kainz, Niklas Haider, Theresa Rienmüller, Kerstin Lenk, Rupert Kargl, Michele Terzano, Gerhard Sommer, Gerhard A. Holzapfel, Julia Fuchs   +9 more
wiley   +1 more source

In Vivo Comparison of Ultimate Tensile Strength of Nickel-Titanium Aligning Archwires Exposed to Fluoridated Mouthwash

Orthodontic Journal of Nepal, 2020
Introduction: Orthodontists usually prescribe fluoridated mouthwash to their patients to mitigate risk of dental caries. These mouthwashes may alter the mechanical properties of archwires by dissolving the protective oxide-layer.
Pasupureddi Keerthana, Prasad Chitra, Puneeth S B, LS Lokesh Janardhanam   +3 more
doaj   +1 more source

POSS‐PEG‐NHS and GSH Cocrosslink DPAV to Prepare Anticalcification Bioprosthetic Scaffold With Enhanced Reendothelization, Anti‐inflammation, and Anti‐ROS

Advanced Healthcare Materials, EarlyView.
POSS‐PEG‐NHS and GSH cocrosslinked DPAV to prepare a multifunctional anticalcification valve substitute. This modification enhances mechanical properties, hemocompatibility, and re‐endothelialization while promoting anti‐inflammatory M2 macrophage infiltration and reducing calcification.
Yuqing Zhang, Chen Qian, Yingjie He, Jingli Ding, Binhao Zhang, Minghui Zou, Xing Chen, Jinping Zhao, Cuifen Lu, Jinping Liu, Jianliang Zhou   +10 more
wiley   +1 more source

MULTI-OBJECTIVE NEURAL NETWORK MODELING FOR IMPROVING STUD ARC WELDING PROCESS JOINING [PDF]

Journal of Engineering Science and Technology, 2011
An effective stud weld algorithm has been developed using a tensile strength response. A multi objectives neural network modeling was used to get higher tensile strength with lower variance.
RIYADH MOHAMMED ALI HAMZA
doaj  

Multifunctional Catechol‐Functionalized Cellulose Hydrogels for the Minimally Invasive Treatment of Acute Optic Nerve Injuries

Advanced Healthcare Materials, EarlyView.
Catechol‐functionalized cellulose hydrogels are developed as injectable, bioadhesive platforms for retinal neuroprotection. The hydrogels exhibit tunable rheological and mechanical properties, strong tissue adhesion, and sustained antioxidative activity.
Kai‐Hsiang Chang, Yi‐Ke Lin, Wei‐Li Chen, Ta‐Ching Chen, Jiashing Yu   +4 more
wiley   +1 more source

Tough, Ductile, and Strong Hard‐Soft Cementitious Composite Enabled by Multi‐Material Additive Manufacturing

Advanced Materials, EarlyView.
Drawing inspiration from the layered hard‐soft architecture found in sea sponges, this work establishes a new framework for architected cementitious composites (ACC) through multi‐material additive manufacturing (MMAM) process. The integration of mortar and elastomer phases into layered architectures enables synergistic toughening mechanisms, including
Aimane Najmeddine, Shashank Gupta, William Makinen, Zayvinn Lin, Krystal Delnoce, Reza Moini   +5 more
wiley   +1 more source

Microstructural and Mechanical Characterization of Wire Arc Additive Manufactured Stainless Steel 316L [PDF]

Archives of Metallurgy and Materials
Robotic arm technology coupled with Cold metal transfer (CMT) has revolutionized Wire arc additive manufacturing (WAAM), gaining widespread recognition in the aerospace, marine, and automotive sectors.
S. KumarJain, Q. Murtaza, P. Singh
doaj   +1 more source

Assessment and statistical correlation of mechanical properties of double sided single pass submerged arc welded line pipe steel

Engineering Science and Technology, an International Journal, 2020
This study aims to assess mechanical properties of submerged arc welded, high-strength, line pipe steel API X70. The obtained weldment as well as the base metal were assessed for strength, ductility, hardness, toughness and weldability.
Adel Saoudi, Mamoun Fellah, Amel Sedik, Djahida Lerari, Farida Khamouli, L'hadi Atoui, Khaldoun Bachari   +6 more
doaj   +1 more source