Results 121 to 130 of about 242,502 (308)

Ultrasonic phased array flexible coupling detection of defects in high-voltage cable terminal lead seals

Frontiers in Mechanical Engineering
High-voltage cable terminal lead seals may develop defects such as holes, cracks, or delamination due to substandard installation quality or external forces during operation.
Peng Ziping, Zheng Jishi, Zhen Zhiming, Huang Yaosheng, Li Xiaobin, Cai Qiushen   +5 more
doaj   +1 more source

Development of Sustainable MgO–C Refractories Using MgO–C Recyclates and a Novel Eco‐Friendly Fructose–Tannin Binder Crosslinked With Citric Acid

Advanced Engineering Materials, EarlyView.
This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar, Jana Hubálková, Steffen Dudczig, Gert Schmidt, Florian Kerber, Thomas Schemmel, Patrick Gehre, Christos G. Aneziris   +7 more
wiley   +1 more source

Deterministic Detection of Single Ion Implantation

Advanced Engineering Materials, EarlyView.
Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead, Lok Kan Wan, Maddison Coke, Janet Jacobs, Nicholas F. L. Collins, Mark C. Rosamond, Richard J. Curry   +6 more
wiley   +1 more source

Comparison of extraction methods for analysis of flavonoids in onions [PDF]

, 2008
Onions are known to contain high levels of flavonoids and a comparison of the efficiency, reproducibility and detection limits of various extraction methods has been made in order to develop fast and reliable analytical methods for analysis of flavonoids
Knuthsen, Pia, Nielsen, John, Soeltoft, Malene   +2 more
core  

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, EarlyView.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

A wireless ultrasonic NDT sensor system [PDF]

, 2005
Ultrasonic condition monitoring technologies have been traditionally utilized in industrial and construction environments where structural integrity is of concern.
Benny, C.G., Hayward, G., McNab, A., Steel, K.   +3 more
core  

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Ultrasonic detection of fetal persistent right umbilical vein and incidence and significance of concomitant anomalies. [PDF]

BMC Pregnancy Childbirth, 2020
Li J, Yuan Q, Ding H, Yang Z, Wang B, Wang B.   +5 more
europepmc   +1 more source

Understanding the Stochastic Nature of Process Parameter Development of Blown Powder Laser Beam Directed Energy Deposition Additive Manufacturing of Pure Molybdenum

Advanced Engineering Materials, EarlyView.
Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies, Daniel E. Driemeyer, Aaron P. Stebner   +2 more
wiley   +1 more source