Results 61 to 70 of about 39,376 (341)

A Novel Model of Ultrasonic Fatigue Test in Pure Bending

Materials, 2022
The very high cycle fatigue (VHCF) failure of in-service components is mainly caused by the vibration of thin-wall elements at a high frequency. In this work, a novel model of ultrasonic fatigue test was developed to test thin-wall material in bending up to VHCF with an accelerated frequency.
Dongtong Yang, Sen Tang, Yongtao Hu, Alexander Nikitin, Qingyuan Wang, Yongjie Liu, Lang Li, Chao He, Yan Li, Bo Xu, Chong Wang   +10 more
openaire   +2 more sources

The Discontinuous Carbon Fiber Composite: a Review of the Damage Characteristics [PDF]

, 2015
Discontinuous carbon fiber composite (DCFC) is one of new low-cost material product form that had applied for commercial component such as window frames of the Boeing 787 Dreamliner.
Bale, J. (Jefri)
core  

Development of Sustainable MgO–C Refractories Using MgO–C Recyclates and a Novel Eco‐Friendly Fructose–Tannin Binder Crosslinked With Citric Acid

Advanced Engineering Materials, EarlyView.
This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar, Jana Hubálková, Steffen Dudczig, Gert Schmidt, Florian Kerber, Thomas Schemmel, Patrick Gehre, Christos G. Aneziris   +7 more
wiley   +1 more source

NIMS fatigue data sheet on gigacycle fatigue properties of A2017 (Al-4.0Cu-0.6Mg) aluminium alloy

Science and Technology of Advanced Materials: Methods
The new fatigue data sheets, Nos. 135 and 136, disclose the gigacycle fatigue properties of A2017-T4 aluminium alloys. No. 135 shows gigacycle fatigue test results at a stress ratio of R =  −1 up to 1010 cycles, obtained by rotating bending fatigue ...
Yoshiyuki Furuya, Hideaki Nishikawa, Hisashi Hirukawa   +2 more
doaj   +1 more source

Ultrasonic and Conventional Fatigue Endurance of Aeronautical Aluminum Alloy 7075-T6, with Artificial and Induced Pre-Corrosion

Metals, 2020
Ultrasonic and conventional fatigue tests were carried out on the AISI-SAE AA7075-T6 aluminum alloy, in order to evaluate the effect of artificial and induced pre-corrosion.
Ishvari F. Zuñiga Tello, Marijana Milković, Gonzalo M. Domínguez Almaraz, Nenad Gubeljak   +3 more
doaj   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Multiscale study of fracture in aluminum-magnesium alloy under fatigue and dynamic loading [PDF]

Fracture and Structural Integrity, 2015
In this paper we investigated the influence of consecutive dynamic and gigacycle fatigue loads on the lifetime of aluminum-magnesium alloy AlMg6. Preloading of samples was achieved during dynamic tensile tests in the split-Hopkinson bar device.
Vladimir Oborin, Mikhail Bannikov, Oleg Naimark, Mikhail Sokovikov, Dmitry Bilalov   +4 more
doaj   +2 more sources

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

From Clinic to Computation: Multiscale Bioengineering Strategies for Durable Biological Aortic Valve Replacements

Advanced Functional Materials, EarlyView.
Bioprosthetic aortic valves have revolutionized the treatment of aortic stenosis, but their durability is limited by structural valve deterioration (SVD). This review focuses on the pericardial tissue at the heart of these valves, examining how its mechanical properties and calcification drive fatigue and failure.
Gabriele Greco, Pierfrancesco Gaziano, Serena Anglese, Simone Morganti, Carlo de Vincentiis, Ferdinando Auricchio, Michele Marino, Michele Conti   +7 more
wiley   +1 more source

Decellularized Extracellular Matrix (dECM) in Tendon Regeneration: A Comprehensive Review

Advanced Healthcare Materials, EarlyView.
Decellularized Extracellular Matrix (dECM) offers a promising solution by replicating the native tendon microenvironment and promoting regeneration. This review highlights advances in the decellularization methods, as well as their integration with emerging technologies and translational progress in tendon tissue engineering.
Kumaresan Sakthiabirami, Yeonwoo Park, Seong Kyeong Jo, Min Hee Kim, Jae Hwang Song   +4 more
wiley   +1 more source