Results 161 to 170 of about 733 (200)
Some of the next articles are maybe not open access.
International Journal of Computational Materials Science and Surface Engineering, 2013
This paper gives a brief overview of published results pertinent to ultrasonic shot peening, a relatively new method to introduce severe plastic deformations in the surface of materials and obtain nanosized grains. Among reported benefits are increased surface hardness and fatigue resistance, and possibility to perform nitriding at lower temperatures ...
Qingyou Han, Yanxiong Liu, Fei Yin
exaly +2 more sources
This paper gives a brief overview of published results pertinent to ultrasonic shot peening, a relatively new method to introduce severe plastic deformations in the surface of materials and obtain nanosized grains. Among reported benefits are increased surface hardness and fatigue resistance, and possibility to perform nitriding at lower temperatures ...
Qingyou Han, Yanxiong Liu, Fei Yin
exaly +2 more sources
Modelling of Ultrasonic Shot Peening
Volume 6B: Materials and Fabrication, 2015 Component manufacturing may induce cold work, residual stresses, microstructure changes and even surface defects. This initial condition is usually ignored in component integrity assessments, but can strongly affect its lifetime. For instance, it is well-known that a rough surface finish associated to the presence of tensile residual stresses may favor
Vincent Robin +3 more
core +4 more sources
Overview of ultrasonic shot peening
Surface Engineering, 2017Ultrasonic shot peening (USP) is acknowledged as an effective surface treatment method to enhance the mechanical performance of materials by inducing compressive residual stress in solid metals and alloys. This article overviews recent researches from our group at Purdue University on the USP in the aspects of modelling the kinetics of the shots ...
Fei Yin, Shan Hu, Qingyou Han
exaly +2 more sources
Experimental investigation on ultrasonic shot peening of WC-Co alloy
Materials and Manufacturing Processes, 2020Ultrasonic surface shot peening (USSP) treatment was conducted on the WC-8Co composite. The effects of different USSP-treated time on surface roughness, microstructure, mechanical and corrosion res...
Yifeng Hu, Xuehui Zhang, Tahir Ahmad
exaly +2 more sources
Impact velocity and distribution in ultrasonic shot peening
, 2011 We study the dynamic of shot during an ultrasonic shot peening process from two aspects. The first consists in running various calculations of spheres placed in a cylindrical chamber (radius 35 mm, height 40 mm) and propelled by a sonotrode (frequency 20 kHz, amplitude 25 μm). This allows for a better understanding of the minimal peening time needed to
Badreddine, Jawad +4 more
core +4 more sources
Tribology International, 2015 IF=2.1International audienceThis article assessed the roughness induced by ultrasonic shot peening. Surface properties of AISI 316L steel specimens were modified through the variation of ultrasonic shot-peening parameters (shot material, shot diameter ...
J Marteau +2 more
exaly +2 more sources
Random Approach to Peening Coverage in Ultrasonic Shot-Peening
Materials and Manufacturing Processes, 1995Abstract The so-called ultrasonic shot-peening is a new process using calibrated peening hard balls motioned by walls vibrating at 20000 Hz. As in conventional shot-peening, a fully peened surface coverage is required tor the process to be efficient. However, it is intricate to determine the coverage ratio experimentally. A statistical approach, issued
H. Chardin +3 more
openaire +1 more source
Relation between surface hardening and roughness induced by ultrasonic shot peening
Tribology International, 2015 IF=2.1International audienceThis paper is focused on the identification of a relation between surface hardening and roughness induced by ultrasonic shot peening.
J Marteau, M Bigerelle
exaly +2 more sources
Effect of ultrasonic shot peening on microstructure and properties of 301SS
Materials and Manufacturing Processes, 2017Ultrasonic shot peening (USP) is an efficient way to improve the mechanical behavior of 301 stainless steel by inducing severe plastic deformation on its surface.
Li, Kejian +4 more
openaire +1 more source
Microstructural Evolution of Super304H Upon Ultrasonic Shot Peening and Subsequent Annealing
Journal of Nanoscience and Nanotechnology, 2018In this study we analyze the effect of shot peening on the microstructure and mechanical properties of Super304H, which is widely used for boiler tubes. Specimens were shot peened for 5, 10, and 15 minutes, and then heat treated at 600, 700, and 800 °C for 15 minutes. Vickers hardness was measured and the microstructure of cross sectional specimens was
Kyeongae, Nam +2 more
openaire +2 more sources