Results 121 to 130 of about 336,157 (237)

Strength of joints produced by ultrasonic spot welding of copper plates using tools with different tooth heights

Frontier Materials & Technologies
Ultrasonic welding of metals is an energy-efficient, environmentally friendly technology that allows producing solid-state joints between thin blanks. The widespread use of this technology is hampered by the low strength of the resulting joints and the ...
Elvina R. Shayakhmetova
doaj   +1 more source

Design of High‐Performance MnCo1.5Cu0.5O4 Spinel Contact Material with Optimized Electrical Conductivity and Thermal Stability for Solid Oxide Electrolysis Cells by Cu Doping

ENERGY &ENVIRONMENTAL MATERIALS, Volume 9, Issue 5, September 2026.
Cu‐doped spinel MnCo1.5Cu0.5O4 exhibits excellent conductivity and stability as SOC contact material. After 1000‐h aging at 850 °C, the contact layer maintains a 10 mΩ cm2 ASR value, and a single‐cell stack achieves a H2O/CO2 co‐electrolysis power density of 0.52 W cm−2.
Haozhen Li, Shuai Yuan, Xingtong Mao, Hao Shi, Hengyong Tu, Chao Ma, Lei Zhu, Zhen Huang   +7 more
wiley   +1 more source

Fusion Bonding Possibility for Incompatible Polymers by the Novel Ultrasonic Welding Technology: Effect of Interfacial Compatibilization. [PDF]

ACS Omega, 2022
Fu X, Wu X, Huang G, Li W, Kang S, Wang L, Luo J, Pan Z, Lu W.   +8 more
europepmc   +1 more source

Ultrasonic Welding [PDF]

JOM, 2012
openaire   +1 more source

Entropy‐Driven Innovations: Entropy Stabilized Oxides for High‐Performance Next‐Generation Lithium–Sulfur Batteries

ENERGY &ENVIRONMENTAL MATERIALS, Volume 9, Issue 5, September 2026.
This article explores high‐entropy‐stabilized oxides (HEOs) as novel functional materials for addressing critical issues in lithium–sulfur (Li–S) batteries, including lithium polysulfide (LPS) shuttling, inadequate conductivity, and slow redox kinetics.
Hassan Raza, Jialiang Wei, Zhicai Wang, Zhaoyang Lv, Junye Cheng, Jia Xu, Liang An, Yuliang Liu, Sergey Ryazantsev, Shukui Li, Guangping Zheng   +10 more
wiley   +1 more source

Optimizing Ultrasonic Welding Parameters for Multilayer Lap Joints of PEEK and Carbon Fibers by Neural Network Simulation. [PDF]

Materials (Basel), 2022
Panin SV, Stepanov DY, Byakov AV.
europepmc   +1 more source

Nanoparticle‐Reinforced Ti‐6Al‐4V Metal Matrix Nanocomposites for Additive Manufacturing: Synthesis Methods, Process Optimization, and Performance Enhancements

Engineering Reports, Volume 8, Issue 9, September 2026.
Reinforcing Ti‐6Al‐4V with nanoparticles to form metal matrix nanocomposites (MMNCs) offers a promising solution. This review explores current additive manufacturing approaches for producing Ti‐6Al‐4V metal matrix nanocomposites. Key fabrication parameters, synthesis strategies, and future directions for high‐quality MMNCs in metal additive ...
Precious Onyeji, Abhijit Cholkar, Alan Martin, David Culliton, Ronan McCann, Ramesh Raghavendra   +5 more
wiley   +1 more source

Comprehensive Effect of Arc and Ultrasonic Energy on MIG Arc Ultrasonic Welding. [PDF]

Materials (Basel), 2021
Chen Q, Wang C, Wang Y, Wang J, Lin S, Wang J.   +5 more
europepmc   +1 more source

Experimental and Comparative Study of the Corrosion Behavior of Lean Duplex Stainless Steel in Seawater

Materials and Corrosion, Volume 77, Issue 9, Page 1399-1423, September 2026.
The localized corrosion behavior of lean duplex stainless steel EN 1.4062 is systematically compared with austenitic and higher‐alloyed duplex grades in natural seawater. A clear resistance ranking is established, highlighting EN 1.4062 as a cost‐effective alternative for limited marine exposure.
Mohammad Hassanzadeh, Nicolas Larché, Audrey Allion‐Maurer, Raf Dewil, Barbara Rossi   +4 more
wiley   +1 more source

Integrating Electronics to Textiles by Ultrasonic Welding for Cable-Driven Applications for Smart Textiles. [PDF]

Materials (Basel), 2021
Micus S, Rostami SG, Haupt M, Gresser GT, Meghrazi MA, Eskandarian L.   +5 more
europepmc   +1 more source