Results 41 to 50 of about 6,687 (249)

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Process-integrated resistance spot welding testing using ultrasonic techniques

, 2022
S.345-350 : Ill., Lit.An ultrasonic test technique is presented which determines the temperature changes in the weld spot and weld nugget growth during resistance spotwelding.
Waschkies, E.
core  

Evaluation of Arc Signals, Microstructure and Mechanical Properties in Ultrasonic-Frequency Pulse Underwater Wet Welding Process with Q345 Steel

, 2022
The ultrasonic-frequency pulse underwater wet welding (UFP-UWW) process was achieved through a constant-voltage-mode power source connecting an ultrasonic-frequency pulse power source in parallel.
Chengyu Hu, Wei Zhao, Yucheng Lei, Jianfeng Wang, Hongliang Li, Jibo Wang, Shixiong Liu, Hao Ji   +7 more
core   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Achieving polycrystalline transformation and microstructural segregation reduction of nickel-based single crystal super-alloys by ultrasonic pulse arc welding

Journal of Materials Research and Technology, 2023
The sub-grains coarsening and low melting point eutectic are the internal causes of cracking of single crystal super-alloys in welding. Aiming to overcome two internal causes, in this paper, the effect of ultrasonic pulse arc welding on the grains, sub ...
Yajie Wang, Haodong Wang, Junmei Chen, Yi Zheng, Chuanzong Li, Tongtong Liu, Lu Hao, Zhang Kejin   +7 more
doaj   +1 more source

Feasibility and optimization of dissimilar laser welding components [PDF]

, 2008
Demands placed on dissimilar metals joints have increased from various viewpoints, such as, environmental concerns, energy saving, high performance, cost saving and so on.
Hassan, Ezzeddin Mohamed
core  

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Influence of Single-Sided Ultrasonic Assistance on the Double-Sided Welding Forming Quality of Q355 Thin Plates

Metals
To solve the problems of large deformation and poor welding quality commonly observed during the double-sided welding of Q355 thin plates, this study systematically investigated the effects of single-sided ultrasonic-assisted welding on the weld ...
Peng Yin, Wenkai Li, Chunguang Xu, Zekai Wang, Tingting Hao, Lin Wang   +5 more
doaj   +1 more source

An adaptive control system for off-line programming in robotic gas metal arc welding. [PDF]

, 1997
The aim of this work was to develop an integration concept for using off-line programming in robotic gas metal arc welding of thin sheet steel. Off line -welding parameter optimization and on-line monitoring and adaptive control of process stability ...
Carvalho, G. C.
core  

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source