Results 121 to 130 of about 16,417 (265)

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

open access: yesAdvanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack   +15 more
wiley   +1 more source

Response of a Blood Clot Adherent to Bone, Oral Mucosa and Hard Dental Tissues to a Uniaxial Tensile Test: An In Vitro Study. [PDF]

open access: yesMedicina (Kaunas)
Pellegrini G   +8 more
europepmc   +1 more source

Biomechanics of Fascia Lata - Uniaxial Tensile Test

open access: yes
Human Fascia Lata (FL) is a connective tissue with a multilayered organization also known as aponeurotic fascia. In each layer (usually two or three) the collagen fibers run in parallel directions, forming an angle between the layers that usually varies between 75° and 80°.
openaire   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

open access: yesAdvanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala   +5 more
wiley   +1 more source

Liquid Metal‐Based Stretchable Strain Sensor for Fruit Growth Monitoring

open access: yesAdvanced Materials Technologies, EarlyView.
Schematic overview of the fruit growth sensor development workflow, including sensor fabrication by injection molding, electromechanical and environmental characterization, mechanical stability testing, electronic readout integration, and outdoor field validation for monitoring of fruit growth under practical orchard conditions.
Asad Ullah   +7 more
wiley   +1 more source

Tunable Applicator for Microneedle‐Based Medical Devices

open access: yesAdvanced Materials Technologies, EarlyView.
This paper presents a simple, low‐cost tunable applicator (TAPP) for microneedle array patches that uses a material‐agnostic controlled‐fracture mechanism to ensure reliable skin penetration and uniform array engagement. The scalable, modular design is compatible with injection molding and 3D printing, can be integrated directly into patches, and is ...
Dan Ilyn   +9 more
wiley   +1 more source

3D Printing of Stretchable, Compressible and Conductive Porous Polyurethane for Soft Robotics

open access: yesAdvanced Materials Technologies, EarlyView.
A 3D‐printable porous dopamine‐polyurethane acrylate elastomer results in conductive, stretchable, and compressible structures that can be metallized in situ through catechol‐mediated silver reduction. The resulting material function as both compliant soft robot with a and strain sensors without complex assemblies, enabling fully 3D‐printed soft ...
Ouriel Bliah   +3 more
wiley   +1 more source

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

open access: yesAdvanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang   +9 more
wiley   +1 more source

Home - About - Disclaimer - Privacy