Results 101 to 110 of about 47,827 (268)

Elastomers Combining Damping Efficiency With Rapid Recovery

Advanced Materials Technologies, EarlyView.
Double network granular elastomers (DNGEs) combine high energy dissipation under both cyclic loading and high impact with rapid shape recovery. 3D printing enables the production of complex, customizable structures with tailored performance. Recyclable DNGEs retain their properties over multiple recycling cycles.
Eva Baur, Alain Molleyres, Esther Amstad
wiley   +1 more source

Smart and Sustainable Sizing: Investigating the Sensing Behavior of Glass Fabrics Coated With Waterborne Polyurethane/Graphene Dispersions

Advanced Materials Technologies, EarlyView.
Waterborne polyurethane/graphene formulations are developed as piezoresistive coatings on glass fabric to enable flexible strain sensing. The graphene‐enabled conductive network provides a stable electromechanical response under cyclic compression. The coating demonstrates reliable pressure‐dependent resistance changes, highlighting its potential for ...
Vishnu Vijayan Pillai, Premika Govindaraj, Sai Aditya Pradeep, Olivia Sequerth, Srikanth Pilla, Franz Konstantin Fuss, Peter Kingshott, Nishar Hameed, Nisa V Salim   +8 more
wiley   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Mechanical Fatigue in Liquid‐Metal Interconnects: Failure Mechanism Analysis and Validation of Improvement Strategies

Advanced Materials Technologies, EarlyView.
Multi‐million cycle reliability for liquid metal stretchable electronics is achieved through a continuous cycle of mechanical testing, failure mode and mechanism analysis and implementing subsequent mitigation strategies. ABSTRACT Stretchable electronics that combine mechanical compliance with reliable electrical performance are essential for ...
Lennert Purnal, Maximilian Krack, Parth Vinayakrao Sewlikar, Bart Ruttens, Tom Hauffman, Iris De Graeve, Wim Deferme, Michaël Daenen, Monika Rai   +8 more
wiley   +1 more source

Experimental investigation of residual strain formation mechanisms in composite laminates under cycling loading

Учёные записки Казанского университета: Серия Физико-математические науки, 2017
Cycling tension tests of the specimens from symmetric angle-ply laminate based on ELUR-P unidirectional carbon fiber and XT-118 cold-hardening epoxy have been carried out. Using the obtained experimental results, the process of residual strains formation
V.N. Paimushin, S.A. Kholmogorov, R.A. Kayumov   +2 more
doaj  

Proposal of a Transport Planning Model for the Removal of Quarry Stone Using a Simulation

Applied Sciences
This article describes a transport planning model which applies a simulation to support decision-making in quarry operations. The analysis of the transport system was used as input for creating the model and the subsequent research.
Janka Saderova, Lubomir Ambrisko, Daniela Marasova, Patricia Muchova   +3 more
doaj   +1 more source

Material Selection and Geometric Design for Few‐filament Shape Memory Polymer Yarns for Force Generation

Advanced Materials Technologies, EarlyView.
A custom shape memory polymer material selection process relates quantitative application criteria (e.g., compression garment yarns) to material characterization information. The selected materials are manufactured into yarn geometries, which expand the design space by creating structural stress‐strain profiles beyond the nominal material stress‐strain
Michaela Andrews, Susan Mantell, Julianna Abel   +2 more
wiley   +1 more source

Research on Numerical Simulation of the Influence of Valley Down-cutting on Unloading of Bank Slope

Renmin Zhujiang, 2020
In order to obtain the influence on unloading of bank slope during the process of valley down-cutting, this paper takes the bank slope at the lower dam site of a hydropower station as the research object, and analyzes the stress field characteristics ...
LI Wancai, DENG Hui, SU Hang, DING Zhonghui, LU Bifeng, HAO Hao, LI Anrun   +6 more
doaj  

Liquid Metal‐Based Stretchable Strain Sensor for Fruit Growth Monitoring

Advanced Materials Technologies, EarlyView.
Schematic overview of the fruit growth sensor development workflow, including sensor fabrication by injection molding, electromechanical and environmental characterization, mechanical stability testing, electronic readout integration, and outdoor field validation for monitoring of fruit growth under practical orchard conditions.
Asad Ullah, Lennert Purnal, Maximilian Krack, Sander Vijgen, Thijs Vandenryt, Dieter Reenaers, Ronald Thoelen, Wim Deferme   +7 more
wiley   +1 more source

Dynamic Current Routing in Conductive Liquid Crystal Elastomers for Complex Deformation Actuators

Advanced Materials Technologies, EarlyView.
This work introduces a novel actuation control strategy in which electrical stimulation generates localized Joule heating in conductive liquid crystal elastomer (LCE) surfaces, enabling complex 3D deformations from a single homogeneous surface without preprogramming.
Gloria PouWai Lei, Morgan Barnes, Thomas George Thuruthel   +2 more
wiley   +1 more source