Results 111 to 120 of about 94,789 (264)

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

The effect of IS SERVQUAL and user information satisfaction (UIS) adoption on user satisfaction

Uncertain Supply Chain Management, 2020
Yohan Wismantoro, Heribertus Himawan, Karis Widiyatmoko   +2 more
openaire   +1 more source

Ontology‐Aligned Structuring and Reuse of Multimodal Materials Data and Workflows Toward Automatic Reproduction

Advanced Engineering Materials, EarlyView.
Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari, Abril Azocar Guzman, Sarath Menon, Stefan Sandfeld, Tilmann Hickel, Markus Stricker   +5 more
wiley   +1 more source

Perceived Time Spent on TikTok, Overall User Satisfaction, and Parallel Psychological Costs. [PDF]

Behav Sci (Basel)
Zhang Q, Yang J, Kim D.
europepmc   +1 more source

Modeling Dislocation Cutting of γ′ Precipitates in Ni‐Base Superalloys: Linking Atomistic and Dislocation Dynamics Simulations

Advanced Engineering Materials, EarlyView.
Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé, Siwen Gao, Marc Fivel, Anxin Ma, Daria Smirnova, Sriram Anand, Arun Prakash, Julien Guénolé, Alexander Hartmaier, Erik Bitzek   +9 more
wiley   +1 more source

Correction: Construction of an evaluation index system for user satisfaction with immersive virtual reality exergaming. [PDF]

Front Psychol
Fu J, Mou N, Gong D, Xu Y, Lu X.
europepmc   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Construction of an evaluation index system for user satisfaction with immersive virtual reality exergaming. [PDF]

Front Psychol
Fu J, Mou N, Gong D, Xu Y, Lu X.
europepmc   +1 more source

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

Research on user satisfaction with AIGC assisted museum scenario design. [PDF]

Sci Rep
Dongjiao Z, Yunlong Z, Xu J.
europepmc   +1 more source