Results 61 to 70 of about 426,682 (298)
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
The concept of vacuum in quantum electrodynamics [PDF]
, 2010 A re-evaluation of the concept of vacuum in quantum electrodynamics is presented, focusing on the vacuum of the quantized electromagnetic field. In contrast to the ‘nothingness’ associated to the idea of classical vacuum, subtle aspects are found in ...
bacelar valente, mario
core
FastNano Liquid: An Automated Platform for Small‐Angle X‐ray Scattering‐Based Materials Discovery
Advanced Engineering Materials, EarlyView.We present FastNano Liquid, an automated small‐ and wide‐angle X‐ray scattering platform for the combined synthesis and characterization of (nano)materials. The platform is coupled to varied reactor workflows for both in situ studies of reaction kinetics and ex situ screening of synthesis conditions to support machine learning‐guided exploration ...
Pierre‐Baptiste Flandrin +16 more
wiley +1 more source
Vacuum assisted closure technique: a short review
The Pan African Medical Journal, 2017 The management of difficult to heal wounds has always been a cause of concern for the treating clinicians. There has been a tremendous increase in the number patients presenting with difficult to heal wounds.
Sankalp Yadav, Gautam Rawal, Mudit Baxi
doaj +1 more source
Advanced Engineering Materials, EarlyView.Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul +5 more
wiley +1 more source
Analysis and evaluation of the teat-end vacuum condition in different automatic milking systems [PDF]
, 2011 peer-reviewedThe number of automatic milking systems (AMSs) installed worldwide shows an increasing trend. In comparison to the preliminary models, new versions employ more sophisticated sensor technology than ever before. The originally developed AMSs
Brunsch, R. +8 more
core +1 more source
Vacuum tourist plan Canberra 1951 [cartographic material] /
, 1951 Street map of Canberra, Australian Capital Territory, printed in dark green, and overprinted in red, showing places of interest with tourist information.
Vacuum Oil Company.
core
Advanced Engineering Materials, EarlyView.This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source
Vacuum road map of Queensland [cartographic material] /
, 1947 Map of Queensland showing main roads with mileage table.; Other title: Road map of Queensland.; Situation date determined from inset signed "WHH '47".; Also available in an electronic version via the internet at: http://nla.gov.au/nla.map-vn2271935 ...
Vacuum Oil Company.
core
Fabrication of Energy Efficient Vacuum Glazing using a Novel Edge Sealing Material [PDF]
, 2013 This poster aims at presenting an experimental investigations for the fabrication of vacuum glazing using a novel low-temperature edge sealing material, melts at around 200 C, as shown in figure 1.
Memon, S, Eames, PC
core