Results 181 to 190 of about 8,089 (264)

Load‐Bearing Characteristics of SLA‐Fabricated Octahedral Porous Structures

Strain, Volume 62, Issue 2, April 2026.
A combined experimental–numerical framework was developed to evaluate SLA–fabricated octahedral and pillar–reinforced lattice structures under compression, shear, and torsion. Small increases in infill density produced nonlinear gains in stiffness and strength, reaching a 255% rise in elastic modulus at low porosity. Pillar reinforcement enhanced shear
Mehmet Kir, Umran Esendemir, Mehmet Fahri Sarac   +2 more
wiley   +1 more source

Mechanical Characterization of Fused Deposition Modeling‐Printed Wood‐Polylactic Acid Composites Under Water Conditioning

Polymer Composites, Volume 47, Issue 6, Page 5205-5221, 20 March 2026.
Graphical abstract illustrating the fabrication of PLA and wood‐PLA composites via FDM and their subsequent mechanical testing, water absorption, and re‐drying evaluation. ABSTRACT Natural fiber‐reinforced thermoplastic composites have gained increasing attention due to their sustainability.
Weilong Xu, Meiyu Li, Yanan Xu, Ali Entezari, Jianguang Fang   +4 more
wiley   +1 more source

Piezoresistive Natural Rubber Composites: A Comparison Between Low‐Temperature Glutaraldehyde Curing Agents and Conventional Sulfur Curing Systems

Polymer Composites, Volume 47, Issue 5, Page 4310-4325, 10 March 2026.
The secondary electrical signal peak during cyclic experiment observed in S‐cured NR sensors was eliminated with GA curing due to the homogeneous distribution of crosslink points in the GA‐cured NR network. ABSTRACT This study examines the piezoresistive behavior of natural rubber (NR) composites cured with sulfur (S) and glutaraldehyde (GA) and ...
Rawiporn Promsung, Arthittaya Chuaybamrung, Antonia Georgopoulou, Yeampon Nakaramontri, Frank Clemens, Ekwipoo Kalkornsurapranee   +5 more
wiley   +1 more source

Mechanical Characterization of Additively Manufactured Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) Biopolymer

Journal of Applied Polymer Science, Volume 143, Issue 9, March 5, 2026.
Thermal behavior, specimen fabrication, and mechanical benchmarking of PHBH produced by additive manufacturing and injection molding. ABSTRACT Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHBH) is a biodegradable polyester with strong potential for marine and packaging applications common for thermoplastic polymers, yet its performance after being ...
Lorenzo De Noni, Sara West, Hudson Legendre, Hung‐Jue Sue, Albert E. Patterson   +4 more
wiley   +1 more source

4D Printing of Self‐Immolative Polymers

Advanced Functional Materials, Volume 36, Issue 23, 19 March 2026.
The integration of self‐immolative polymers (SIPs) into light‐based 3D printed structures is presented as a new “living” 4D printing strategy. By exploiting their metastability and stimuli‐responsiveness, SIP‐containing printed objects can undergo rapid and triggered degrowth under ambient conditions and subsequent regrowth through polymer ...
Johannes Markhart, Philipp Mainik, Pia S. Klee, Eva Blasco   +3 more
wiley   +1 more source

Additive Manufacturing of Molecular Architecture Encoded Stretchable Polyethylene Glycol Hydrogels and Elastomers

Advanced Materials, Volume 38, Issue 15, 12 March 2026.
Bottlebrush molecular architecture prevents the crystallization of high molecular weight polyethylene glycol (PEG) based polymers, enabling highly stretchable photocurable PEG hydrogels and elastomers for high‐performance conductive solvent‐free electrolytes at room temperature and for additive manufacturing of complex architectures and multi‐material ...
Baiqiang Huang, Myoeum Kim, Pu Zhang, Emmanuel Oduro, Daniel A. Rau, Li‐Heng Cai   +5 more
wiley   +1 more source

Comparative evaluation of mechanical properties between dual-layer and bonded three-dimensional printed denture base materials: An in vitro study. [PDF]

J Indian Prosthodont Soc
Chander NG, Deshmukh AS, Prakash HG, Srinivasan VK.   +3 more
europepmc   +1 more source

Building like a Coral—Parallelized, Multiscale Biofabrication

Advanced Materials, Volume 38, Issue 17, 20 March 2026.
Corals build stiff, strong, and inherently circular skeletal materials under resource‐ and energy‐limited conditions—offering blueprints for transformative materials. We synthesize the current understanding of coral biomineralization and reframe coral growth as a multiscale, parallelized biofabrication process.
Asma Rehman, Marta Peña Fernández, Kristina K. Beck, Gavin L. Foster, Sebastian J. Hennige, Uwe Wolfram   +5 more
wiley   +1 more source

RAFT-Mediated 3D Printing of Polylactones/Itaconate Elastomers with Polypeptide Surface Functionalization. [PDF]

ACS Polym Au
Bartolini Torres G, Xia T, Yu D, Thijssen Q, Van Vlierberghe S, Li B, Heise A.   +6 more
europepmc   +1 more source

Programmable Dimensional Lithography with Digital Micromirror Devices for Multifunctional Microarchitectures

Advanced Materials Technologies, Volume 11, Issue 5, 6 March 2026.
This review explores recent advances in digital micromirror device (DMD)‐based lithography, focusing on its programmable light modulation, multi‐material compatibility, and dimensional patterning strategies. It highlights innovations from optical system design to materials integration and multifunctional applications, positioning DMD lithography as a ...
Yubin Lee, Byungcheon Yoo, Chaeyeong Ryu, Jongwon Oh, Dahye Baek, Jiseok Lee   +5 more
wiley   +1 more source