Results 111 to 120 of about 683,357 (240)
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
An experimental investigation of retro-reinforced clay brick arches
, 2010 This paper describes the laboratory testing of eight 2.95m span segmental profile clay brick arches. Seven of the arches were strengthened with longitudinal intrados (soffit) reinforcement; the eighth was left unreinforced as an experimental control ...
Ashour, AF, Chen, Y, Garrity, SW
core
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
THE INFERENCE METHOD OF WHEEL LOAD BASED ON THE ACCELERATION OF AXLE HEAD
Jixie qiangdu, 2016 A new load spectrum measuring method which can instead of the six-component measuring wheel was carried out in this paper. Through analysis the signal time-domain,a linear model between the axle head and the wheel was established.
ZHENG SongLin +4 more
doaj
FEA of SFRC three ribbed wall panel / Azrul Md Din [PDF]
, 2014 This finite element study was carried out to investigate the steel fibre reinforced concrete with three (3) ribbed wall (SFRC-3RW) panel containing reinforced wire mesh (BRC) subjected to axial and eccentric loading also its load bearing response ...
Md Din, Azrul
core
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm +6 more
wiley +1 more source
PLoS ONEIn practical engineering, pile foundation will be subject to the combined action of vertical and Rayleigh wave, and the existence of vertical dynamic load will cause the second-order effect that will lead to the increase of horizontal displacement.
Sitong Zhao +5 more
doaj +1 more source
A mechanical design team was formed to design a foot for the lunar utility vehicle SKITTER. The primary design was constrained to be a ski pole design compatible with the existing femur-tibia design legs.
Choi, Gene +5 more
core +1 more source