Results 41 to 50 of about 13,181 (166)

Analisa Pengaruh Desain Gritcone terhadap Pola Patahan Gritcone pada Vertical Roller Mill dengan simulasi Explicit Dynamic (LS-DYNA)

Jurnal Teknik ITS, 2017
Polysius Vertical Roller Mill adalah coal mill yang digunakan PT Holcim Indonesia untuk menggiling batubara bituminous untuk bahan bakar rotary kiln.
Andika Rizaldy, Mas Irfan P Hidayat, Mas Irfan P Hidayat, Rochman Rochiem, Rochman Rochiem   +4 more
doaj  

Investigation of experimental study of end milling of CFRP composite

Science and Engineering of Composite Materials, 2015
Carbon fiber-reinforced plastic (CFRP) composites are materials that are difficult to machine due to the anisotropic and heterogeneous properties of the material and poor surface quality, which can be seen during the machining process.
Kiliçkap Erol, Yardimeden Ahmet, Çelik Yahya Hışman   +2 more
doaj   +1 more source

STUDY ON THE NON-LINEAR VIBRATION IN THE HYDRAULIC SCREW DOWN VERTICAL SYSTEM FOR ROLLING MILL

Jixie qiangdu, 2016
For vertical vibration systems tend to ignore the influence of hydraulic screw down system in the rolling mill,two degrees of freedom hydraulic screw down vertical vibration system model was established based on viscous damping between the hydraulic ...
ZHANG RuiCheng, MA YinZhou, GAO Zheng, WEN JiaHe   +3 more
doaj  

平立两用轧机中离合接手的改进实践

Jixie chuandong, 2010
Practice and application of clutch of the horizontal and vertical dual mill in the rolling are analyzed,and design flaw,technical adjustment are improved.The cost and the accident rate are reduced.
王松, 薛林涛
doaj  

Vertical Vibration Model for Unsteady Lubrication in Rolls-Strip Interface of Cold Rolling Mills

Advances in Mechanical Engineering, 2012
According to the vertical vibration phenomena existing in cold rolling mills, the unsteady lubrication mechanism in roll gap and its influence to rolling stability was chosen as the case for analysis.
Xu Yang, Qing Li, Chao-nan Tong, Qi-han Liu   +3 more
doaj   +1 more source

Case Study: A Practical Application of an Aerosol Treatment in a Commercial Mill

Insects, 2019
In recent years, there has been an increasing interest and need for alternatives to structural fumigations, and one alternative that has been used across the industry is aerosol insecticides.
Deanna S. Scheff, Daniel Brabec, James F. Campbell, Frank H. Arthur   +3 more
doaj   +1 more source

Recovery of vertical mill ATOX 32.5 for limestone milling by weld

, 2011
The wearing is a phenomenon of degradation of different materials by abrasion effects, impact, fatigue, erosion and corrosion among others. This phenomenon carries great lost economic by deterioration of machines elements and industrial equipment, also a highest quota in environmental impact.
Zapata Meneses, Alberto, Marulanda Arévalo, José Luddey, Molina Zapata, José Vidal   +2 more
openaire   +1 more source

Development and Validation of a Simplified Laboratory Test to Design Vertical Stirred Mills

KONA Powder and Particle Journal, 2019
The use of vertical stirred mills in the mining industry has increased remarkably over the past few decades as a result of the growing demand for finer ore grinding.
Maurício G. Bergerman, Homero Delboni Junior   +1 more
doaj   +1 more source

Pemilihan Teknologi Sterilizer Pada Pabrik Kelapa Sawit Menggunakan Metode Analytical Hierarchy Process

Jurnal Teknik Industri, 2014
In Indonesia, the increasing area of palm oil plantation has been followed by the increasing number of palm oil mills from 205 units in 1998 to 695 units in 2012.
S Subiyanto
doaj   +1 more source

DYNAMICS ANALYSIS AND CONTROL OF ROLLING MILL VIBRATION SYSTEM WITH NONLINEAR VIBRATION ABSORBER

Jixie qiangdu
Aiming at the problem of nonlinear vertical vibration control during the dynamic rolling of strip mills, a nonlinear vibration absorber with the disc spring was designed.
LIU Fei, FENG Mengyu, MA Chao, LUO Ruixue   +3 more
doaj