Results 161 to 170 of about 55,060 (259)
International Journal of Applied Ceramic Technology, Volume 23, Issue 2, April 2026.This graphical abstract illustrates the systematic investigation of Spark Plasma Sintering (SPS) parameters, temperature, pressure, and dwell time, on the densification and mechanical performance of ZrB2–20 vol% SiC composites. It highlights the critical influence of powder processing history (WC vs.
Prakhar Jindal +5 more
wiley +1 more source
Short curing time bulk fill composite systems: volumetric shrinkage, degree of conversion and Vickers hardness. [PDF]
Braz Oral ResSampaio CS +5 more
europepmc +1 more source
Microstructural and Thermal Evolution of Turbostratic and Crystalline hBN Using SPS With In‐Situ YAG
Journal of the American Ceramic Society, Volume 109, Issue 4, April 2026.hBN ceramics with an in‐situ formed YAG phase were fabricated by SPS using turbostratic and crystalline powders. The results show that the microstructure, textural orientation, and functional properties of hBN ceramics can be significantly controlled by sintering temperature, starting powder structure, and additives.
Zuhal Yılmaz
wiley +1 more source
Advanced Engineering Materials, Volume 28, Issue 6, 18 March 2026.Excellent combinations of strength and impact toughness are obtained in a bilayer composite of high‐strength carbide‐free bainitic (CFB) steel and high‐ductility twinning‐induced plasticity (TWIP) steel. The composite absorbs energy at small strains when the notch is placed on the TWIP side and at high strains when the notch is placed on the CFB side ...
Kendra Hawke +5 more
wiley +1 more source
Polymer Composites, Volume 47, Issue 5, Page 4102-4126, 10 March 2026.Comparison of experimental and model‐predicted erosion rates for carbon fibre‐reinforced polymer (CFRP) and glass fibre‐reinforced polymer (GFRP) under low‐velocity (2 m/s) and at varying angles and sand concentrations (0.0, 0.05, 0.4 g/L). The results demonstrate good agreement between experimental data and model predictions across different erosive ...
Ali Al‐Darraji +4 more
wiley +1 more source
Advanced Engineering Materials, Volume 28, Issue 5, 4 March 2026.Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley +1 more source
Advanced Materials, Volume 38, Issue 16, 17 March 2026.Sodium Metal All‐Solid State Batteries (Na‐ASSBs) are enabled by the synthesis of the solid state electrolyte, NASICON (Na1+xZr2SixP3‐xO12), using carbide‐based precursor compounds (ZrC and SiC); resulting in dense, pure, and mechanically improved microstructure.
Callum J. Campbell +10 more
wiley +1 more source
Use of Artificial Neural Network in Determination of Shade, Light Curing Unit, and Composite Parameters' Effect on Bottom/Top Vickers Hardness Ratio of Composites. [PDF]
Biomed Res Int, 2018 Deniz Arısu H +6 more
europepmc +1 more source
Advanced Science, Volume 13, Issue 16, 18 March 2026.A computationally designed, cobalt‐free maraging steel tailored for additive manufacturing achieves an ultra‐high tensile strength of 2.3 GPa with 5.7% elongation. This exceptional strength‐ductility synergy stems from high‐density core‐shell Ni3Ti/NiAl nanoprecipitates, a crack‐resistant composition, and a fine equiaxed grain structure enabled by ...
Hu Li +6 more
wiley +1 more source
Thermoelectric Property Mapping for High‐Performance Integrated MgAgSb‐MgCuSb System
Advanced Science, Volume 13, Issue 17, 23 March 2026.From the property mapping of the MgAgSb–MgCuSb system, both thermoelectric materials and corresponding interface materials are optimized: Ag‐rich compositions provide higher PF and zT, whereas Cu‐rich side yields superior transport properties and low contact resistance.
Jiankang Li +5 more
wiley +1 more source