Results 71 to 80 of about 26,893 (289)

Structure and dynamics of Oxide Melts and Glasses : a view from multinuclear and high temperature NMR [PDF]

, 2007
Solid State Nuclear Magnetic Resonance (NMR) experiments allow characterizing the local structure and dynamics of oxide glasses and melts. Thanks to the development of new experiments, it now becomes possible to evidence not only the details of the ...
Cormier, L., Coutures, J. P., Fayon, F., Florian, P., Hiet, J., Massiot, D., Montouillout, V., Neuville, D., Pellerin, N., Roiland, C.   +9 more
core   +6 more sources

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Performance Test on Styrene-Butadiene-Styrene (SBS) Modified Asphalt Based on the Different Evaluation Methods

Applied Sciences, 2019
To uniform the evaluation indicators of Styrene-Butadiene-Styrene (SBS) modified asphalt, the SK70# and SK90# matrix asphalt were modified by different SBS modifier dosage in this study.
Chen Zhang, Hainian Wang, Zhanping You, Junfeng Gao, Muhammad Irfan   +4 more
doaj   +1 more source

New era of cystic fibrosis: full mutational analysis and personalized therapy [PDF]

, 2017
Despite its apparently simple genetics, cystic fibrosis (CF) is a rather complex genetic disease. A lot of variability in the steps of the path from the cystic fibrosis transmembrane conductance regulator (CFTR ) gene to the clinical manifestations ...
Lucarelli, Marco
core   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Performance of rubber-modified asphalt for ultra-thin overlay

Hecheng xiangjiao gongye
　In order to investigate the applicability of rubber-modified asphalt in ultra-thin overlay and to clarify the differences in road performance of different rubber- modified asphalts, the evaluation of the temperature sensitivity, and high- and low ...
WANG He-ping1, ZHANG Li2, LUAN Yang3, WANG Xiao-sen3, MENG Hui-lin3
doaj   +1 more source

Effect of Ulraviolet Light, pH and Temperature on the Thickening Property of Pectin Extracted from Banana, Orange and Lime Peels

Journal of Applied Sciences and Environmental Management, 2019
Pectin is a polysaccharide used as rheology modifier in products such as food and beverages. This work assessed the effect of UV light, pH and temperature on the thickening property of pectin extracted from banana, orange and lime peels.
K.I. Omoniyi, S. Uba, A.I. Aliyu, S. Makama   +3 more
doaj   +1 more source

Mathematical modeling for facilitated transport of Ge(IV) through supported liquid membrane containing Alamine 336 [PDF]

, 2018
A mathematical model was developed for the germanium facilitated transport from a medium containing tartaric acid using Alamine 336 as a carrier. Modeling was carried out based on the extraction constant (Kext) obtained from the liquid-liquid extraction (
Fortuny Sanromá, Agustín, Irannajad, Mehdi, Kamran Haghighi, Hossein, Sastre Requena, Ana María   +3 more
core   +2 more sources

3D (Bio) Printing Combined Fiber Fabrication Methods for Tissue Engineering Applications: Possibilities and Limitations

Advanced Functional Materials, EarlyView.
Biofabrication aims at providing innovative technologies and tools for the fabrication of tissue‐like constructs for tissue engineering and regenerative medicine applications. By integrating multiple biofabrication technologies, such as 3D (bio) printing with fiber fabrication methods, it would be more realistic to reconstruct native tissue's ...
Waseem Kitana, Indra Apsite, Leonid Ionov   +2 more
wiley   +1 more source

Productivity of Gas Condensate Fields Below The Dew Point: A North Sea Case Study [PDF]

, 2011
Imperial Users ...
Lloyd, Phil, Lloyd, Phil
core