Results 181 to 190 of about 51,543 (309)

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Comparison between the mechanical behavior of woven basalt and glass epoxy composites at high strain rates

, 2021
Elmahdy, Ahmed, Verleysen, Patricia
core   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Effect of Preformed Polymeric Microspheres on the Frost Resistance of Low-Clinker Cementitious Composites with Fine Recycled Aggregate. [PDF]

Materials (Basel)
Kępniak M, Panek R, Kalinowski M, Franus W.   +3 more
europepmc   +1 more source

Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC

Advanced Engineering Materials, EarlyView.
ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko, Evelyn Wang, Michael A. Hickner   +2 more
wiley   +1 more source

Enhancing tensile strength of 3D-printed wood-PLA composites via a particle swarm optimization framework. [PDF]

PLoS One
Bhattacharjee B, Mathiyalagan P, Prasad KV, Thatoi DN, Singh V, Kumar GS, K R, Panda JK.   +7 more
europepmc   +1 more source

Inertial effects during the infiltration of an elastic porous medium [PDF]

, 2004
C. Truesdell, D. Ambrosi, D. Ambrosi, D. Ambrosi, D. Antonelli, E. Lacoste, I.S. Liu, J. Bear, K. Wilmanski, K. Wilmanski, L. Mesin, L. Preziosi, M.A. Biot, M.A. Biot, M.A. Biot, M.A. Biot, M.R. Kamal, P. Bassanini, R. Boer De, R. Larsson, S. Sourour, W. Jager, W.B. Young, Y.R. Kim   +23 more
core   +1 more source

Investigation of Thermo‐Chemical Processes in Commercial MgO‐C Refractory Bricks With and Without MgO‐C Recyclate at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm, Jana Hubálková, Christian Schimpf, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +6 more
wiley   +1 more source

Quantitative assessment of alkali and carbon nanotube reinforcement effects on the tensile reliability of sustainable sisal fiber bio-based epoxy composites. [PDF]

Sci Rep
Joshi K, Hiremath P, Hiremath S, Ghewade DV, Vishwanatha HM, Keshyagol K.   +5 more
europepmc   +1 more source