Results 161 to 170 of about 737,182 (294)

Hybrid AI and semiconductor approaches for power quality improvement. [PDF]

Sci Rep
Chinthaginjala R, Srinivasulu A, Agrawal A, Kim TH, Tera SP, Ahmad S.   +5 more
europepmc   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

Multiscale detection of power quality disturbances and cyber intrusions in smart grids using NSCT and frequency band scalograms. [PDF]

Sci Rep
Sinha P, Paul K, Snehalika S, Kasireddy I, Krishna AB, Naga Malleswara Rao DS, Shuaibu HA, Ustun TS.   +7 more
europepmc   +1 more source

Voltage Sag/ Voltage Swell Compensation and Harmonic Distortion using Dynamic Voltage Restorer

IJIREEICE, 2015
Geetha Krishna T, Damodar Reddy M
openaire   +1 more source

Detection of Voltage Fluctuations in Low-Voltage Power Distribution Networks with Principal Component Analysis

, 2019
Comunicació presentada a "Tenth Protection, Automation and Control (PAC) World Conference", celebrada del 17 al 20 de juny de 2019 a la University of Strathclyde a Glasgow, UKPAC World Conference (10th: 2019: Glasgow,UK)This work presents the development
Souto, Laiz, Herraiz Jaramillo, Sergio, Meléndez i Frigola, Joaquim, Torrent-Fontbona, Ferran   +3 more
core  

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

SVPWM based active filtering control of dual inverter fed open-end winding induction motor drive for harmonic mitigation. [PDF]

Sci Rep
Latha SN, Egeriose SK, Gopinathan S.
europepmc   +1 more source

Investigation into voltage and process variation-aware manufacturing test

, 2009
Increasing integration and complexity in IC design provides challenges for manufacturing testing. This thesis studies how process and supply voltage variation influence defect behaviour to determine the impact on manufacturing test cost and quality.
Ingelsson, Bo Urban
core  

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

IoT enabled smart power quality analysis in three phase electrical systems with practical implementation. [PDF]

Sci Rep
Mallala B, Manyam RR, Saini J, Tajuddin MFN, Thanikanti SB.   +4 more
europepmc   +1 more source