Results 121 to 130 of about 32,845 (295)
Advanced Engineering Materials, EarlyView.A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du +4 more
wiley +1 more source
, 2013 [[abstract]]In recent years, the improvement of scientific techniques has significantly promoted the quality of peoples lives as well as concepts of health care.
林卿慧;LIN, CHING-HUI
core
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
The Galactic Disk North–South Asymmetry in Metallicity May Be a New Tracer for the Disk Warp
The Astrophysical Journal LettersGalactic disk warp has been widely characterized by stellar distributions and stellar kinematics but has not been traced by stellar chemistry. Here, we use a sample with over 170,000 red clump (RC) stars selected from LAMOST and APOGEE first to establish
Weixiang Sun +3 more
doaj +1 more source
, 2006 We describe a new processing architecture, known as a warp processor, that utilizes a fieldprogrammable gate array (FPGA) to improve the speed and energy consumption of a software binary executing on a microprocessor. Unlike previous approaches that also
Greg Stitt, Frank Vahid, Roman Lysecky
core
Advanced Engineering Materials, EarlyView.The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat +5 more
wiley +1 more source
, 2010 Photo from Dimen Village of the warp layers wound on the beam. The layers are separated by warping sticks.https://scholarlycommons.pacific.edu/kam-photos/1892/thumbnail ...
Lee, Marie Anna
core
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
Investigation of initial warp tension and weave influence on warp yarn diameter projections /
, 2013 The influence of initial warp yarn tension and fabric weave on warp yarn projections are investigated in this article. Fabrics were woven with different initial tensions and weaves. The warp yarn projections were measured beside the floats in the central
Rukuižienė, Žaneta, +1 more
core
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source