Results 191 to 200 of about 5,193,136 (315)

Global Symmetry, Sphericity, and Roundness in Hemisphere Forming of Fabric Reinforcements: Associations With Local Fiber Distortions and a Black‐Box Quality Prediction

Polymer Composites, EarlyView.
Data‐driven assessment of primaryand secondary quality metrics in hemisphere forming of a fabric reinforcement. ABSTRACT An experimental analysis is conducted to identify the effect of design variables on a set of global geometrical quality metrics, including sphericity, roundness, and symmetry, in hemisphere draping of woven fabrics, next to the ...
Sorayya Kazemi, Arash Dalili, Abbas S. Milani   +2 more
wiley   +1 more source

Ultrafast Dynamic Defect Inspection With Computational Neuromorphic Imaging. [PDF]

Adv Sci (Weinh)
Zhu S, Yin Q, Wang C, Huang J, Lam EY.
europepmc   +1 more source

Effect of Designed 3D Reinforcement in Mitigating Machining Damage on CFRP Plates

Polymer Composites, EarlyView.
Effect of Edge Tufting on Surface Quality, Damage, and Mechanical Performance in CFRP Machining: A Comparative Topographical and Structural Analysis. ABSTRACT Composite materials made of carbon fiber‐reinforced epoxy (CFRP) are widely used in aerospace fields due to their high strength‐to‐weight ratio. However, due to low out‐of‐plane resistance, these
Thiago Luiz Lara Oliveira, Daniel Brighenti Bortoluzzi, Antônio Carlos Ancelotti Jr   +2 more
wiley   +1 more source

Geometric Bounds for Low Steklov Eigenvalues of Finite Volume Hyperbolic Surfaces. [PDF]

J Geom Anal
Hassannezhad A, Métras A, Perrin H.
europepmc   +1 more source

Strain Development During Cure of Partially Pre‐Cured Thermosetting Composites Measured With Distributed Fiber Optic Sensors

Polymer Composites, EarlyView.
Schematic representation of the beneficial effect of ply pre‐curing on temperature overshoot, internal strain and warpage during cure of thin and thick thermosetting composites. ABSTRACT Detection of manufacturing‐induced defects in thermosetting composites is crucial to guarantee part quality, safety, and improve manufacturing efficiency.
Francesco Taddei, Giacomo Struzziero, Valentin Ott, Véronique Michaud   +3 more
wiley   +1 more source

Failure modes and mitigations for Bayesian optimization of neuromodulation parameters. [PDF]

J Neural Eng
Dastin-van Rijn EM, Widge AS.
europepmc   +1 more source

Fused Filament Fabrication and Recycling of Bio‐Based Polyamide 11 Reinforced With Recycled Short Carbon Fibers

Polymer Composites, EarlyView.
Fused Filament Fabrication and Recycling of Bio‐Based Polyamide 11 Reinforced With Recycled Short Carbon Fibers. Sample preparation, mechanical properties improvement after rCF addition and properties retainment after recycling. ABSTRACT This research investigates the fused filament fabrication (FFF) and recycling of bio‐based polyamide 11 (PA11 ...
Mirko Coser, Daniele Rigotti, Alessandro Pegoretti   +2 more
wiley   +1 more source

An image quality transfer approach for localising deep brain stimulation targets. [PDF]

Imaging Neurosci (Camb)
Zheng YQ, Akram H, Li Z, Smith S, Jbabdi S.   +4 more
europepmc   +1 more source

Advance in Structural Battery Technology: Integrating Lithium Titanate to Overcome Limitation of Graphite in Carbon Fabric Composite Structural Batteries

Polymer Composites, EarlyView.
Schematic of manufacturing carbon fabric composite structural batteries. ABSTRACT Structural batteries based on woven carbon fabrics are typically established on lithium ion phosphate (LFP) and graphite. While this method proved viable from the manufacturing perspective, the resulting structural batteries exhibited suboptimal electrochemical ...
Zhibin Han, Yuncong Feng, Wanrui Zhang, Yubo Hu, Yifeng Xiong, Weizhao Zhang   +5 more
wiley   +1 more source

Multi-Frame Image Registration for Automated Ventricular Function Assessment in Single Breath-Hold Cine MRI Using Limited Labels. [PDF]

Magn Reson Med
Ghoul A, Cassal Paulson P, Lingg A, Krumm P, Hammernik K, Rueckert D, Gatidis S, Küstner T.   +7 more
europepmc   +1 more source