Results 31 to 40 of about 153 (98)

Circularity in 3D Printing with Poly(Ethylene Terephthalate Glycol): Copolymer Composition Dependent Degradation During Recycling

Macromolecular Materials and Engineering, Volume 311, Issue 1, January 2026.
Circular recycling of PETG using 3D printing leads to the development of crystalline inclusions of oligomers generated from thermomechanical degradation during recycling. However, the concentration of crystals generated depends on the PETG sourcing that is associated with its molar mass and copolymer composition.
Sierra F. Yost, Jordan C. Smith, Bryan D. Vogt   +2 more
wiley   +1 more source

Wu Gaitian with red thread

, 2010
Photo from Dimen Village of Wu Gaitian preparing to do a rotation on the warping board using red thread. She is standing with her glasses on and looking at the spool.
Lee, Marie Anna
core  

Synergistic Effects of Hybrid Single‐Walled Carbon Nanotube/Carbon Black Fillers in 3D‐Printable Polyamide 6 Nanocomposites: Balancing Electrical Conductivity and Mechanical Performance

Polymer Engineering &Science, Volume 66, Issue 1, Page 364-377, January 2026.
Schematic illustration of PA6/SWCNT/CB nanocomposite development and 3D printing for conductive applications. ABSTRACT Conductive polymer nanocomposites for additive manufacturing face a persistent trade‐off, as achieving electrical conductivity requires filler loadings that impair processability and mechanical integrity.
Müslüm Kaplan
wiley   +1 more source

Adding white warp

, 2010
Photo from Dimen Village of Wu Mnci preparing to add white yarn to the backstrap loom she is warping. She has completed four revolutions around the bench with the black yearn.
Lee, Marie Anna
core  

An Industrial Metaverse Platform for Collaborative and Sustainable Manufacturing in Industry 5.0

IET Collaborative Intelligent Manufacturing, Volume 8, Issue 1, January/December 2026.
This article presents an integrated industrial metaverse platform that combines IoT‐enabled real‐time data acquisition, digital twin modelling and immersive multiuser environments to support human‐centric and sustainable manufacturing in Industry 5.0.
Antonella Petrillo, Aniello Ferraro, Antonio Garofalo, Fabio De Felice   +3 more
wiley   +1 more source

King Philip - Spool and Warping Department. Warper - Young girls sometimes assist. Sometimes a tyer-in comes from her position behind the rack and helps the warper. Light very good in this mill. Location: Fall River, Massachusetts

, 1916
Title from NCLC caption card.In album: Mills.Hine no ...
Hine, Lewis Wickes, 1874-1940, Hine, Lewis Wickes, 1874-1940, photographer.   +1 more
core  

Development of novel filament production setup of continuous fiber reinforced composite filament for additive manufacturing applications. [PDF]

Sci Rep
Jamal MA, Ghafoor U, Shah OR, Qureshi Y, Shah UH.   +4 more
europepmc   +1 more source

Development and Evaluation of a Low-Cost Open-Source Nasometer. [PDF]

Sensors (Basel)
Wang L, Romani A, Adams S, Pearce JM, Parsa V.   +4 more
europepmc   +1 more source

Reducing particulate emissions from 3D printers using low-cost enclosures and engineering controls. [PDF]

Rapid Prototyp J
Barnes C, Dye N, O'Connor C, Hammond D.
europepmc   +1 more source

Development of Natural Fibre-Reinforced Semi-Finished Products with Bio-Based Matrix for Eco-Friendly Composites. [PDF]

Polymers (Basel), 2022
Möhl C, Weimer T, Caliskan M, Baz S, Bauder HJ, Gresser GT.   +5 more
europepmc   +1 more source