Results 11 to 20 of about 500 (181)

Use of Foundry Sands in the Production of Ceramic and Geopolymers for Sustainable Construction Materials

open access: yesApplied Sciences, 2023
The aim of this research was to evaluate the possibility of reusing waste foundry sands derived from the production of cast iron as a secondary raw material for the production of building materials obtained both by high-temperature (ceramic tiles and ...
Caterina Sgarlata   +4 more
doaj   +1 more source

Research on regeneration methods of animal glue waste sand for foundry [PDF]

open access: yesRoyal Society Open Science, 2018
Sand moulds are used in the casting process. However, after heating, the binder in the sand loses the binding properties, and the most part of the foundry sand has to be discarded from the process.
Li Ying-min   +2 more
doaj   +1 more source

Characteristics of Green Concrete with Industrial Wastes as Replacement of Fine and Coarse Aggregate [PDF]

open access: yesE3S Web of Conferences, 2023
Waste generated due to various industrial activities are dumped as landfill posing serious environmental complications. Pollution control due to industrial waste has become one of concern across the globe.
Chakravarthy PolichettyRaja Kalyana   +6 more
doaj   +1 more source

Assessment of Foundry Chromite Sand Crushability under Thermal-Mechanical Loading [PDF]

open access: yesArchives of Foundry Engineering, 2023
When used for sand casting, foundry sand is stressed in several ways. These stresses, thermal and mechanical, compromise the grain integrity, resulting in size reduction and the production of small particles to the point where the sand is no longer ...
J.K. Kabasele, K.D. Nyembwe, H. Polzin
doaj   +1 more source

Can waste foundry sand fully replace structural concrete sand? [PDF]

open access: yesJournal of Material Cycles and Waste Management, 2018
Foundry sand (FS) waste creates a serious solid waste management problem worldwide due to the high volumes produced, necessitating alternatives to landfilling. A possible route is its use in concrete; however, the current consensus is that FS can only be used for modest sand replacements, based mostly on evidence on concrete with clay-bound FS ...
Maria Mavroulidou, David Lawrence
openaire   +1 more source

A New Approach in Recycling Waste Foundry Sand for the Preparation of Porous Silicon Powder

open access: yesInternational Journal of Electrochemical Science, 2020
Disposal of waste foundry sand is still one of the most critical challenges faced by the foundry industry. The recycling and reusing of waste foundry sand not only lead to a saving of naturally abundant sand sources but also enhance the sustainability of
Rongfu Xu   +3 more
doaj   +1 more source

Effect of Adding Used-Foundry Sand on Hot Asphalt Mixtures Performance [PDF]

open access: yesEngineering and Technology Journal, 2016
Highway material researchers have been investigating the use ofbyproduct materials such as used-foundry sand as a fine aggregate and mineral filler in asphaltic concrete mixtures to replace the traditional asphalt mixes by new one contain this type of ...
Hasan Hamodi Joni, Hussein HamelZghair
doaj   +1 more source

Recovery of Silicon Dioxide from Waste Foundry Sand and Alkaline Activation of Desilicated Foundry Sand [PDF]

open access: yesJournal of Sustainable Metallurgy, 2020
Abstract This study was conducted to recover silica (desilication) as a valuable metalloid from waste foundry sand (WFS) by a leaching process and to find application for desilicated foundry sand (DFS). The leaching time applied was 5 h; 3 M of potassium hydroxide (KOH) was used as a leaching reagent.
Tebogo Mashifana, Thandiwe Sithole
openaire   +1 more source

Effect of Foundry Sand and Mineral Admixtures on Mechanical Properties of Concrete

open access: yesArchives of Civil Engineering, 2018
Foundry sand waste can be utilized for the preparation of concrete as a partial replacement of sand. The strength properties of M25 grade concrete are studied with different percentages of replacement of fine aggregates by foundry sand at 0%, 10%, 20 ...
Sastry K.V.S.Gopala Krishna   +2 more
doaj   +1 more source

Thermal reclamation of used sand produced by binder jetting processes [PDF]

open access: yesMATEC Web of Conferences, 2023
The binder jetting process for the manufacturing of sand moulds and cores for foundry applications generates appreciable quantity of used sand. This sand is generally discarded to dedicated landfills as a waste management practice in the country.
Thaba Thapelo Precious   +1 more
doaj   +1 more source

Home - About - Disclaimer - Privacy