Results 91 to 100 of about 5,627,035 (251)

Water in the 2003 Virginia General Assembly

, 2003
The 2003 Virginia General Assembly convened on January 8 and adjourned on February 22, with a reconvened (“veto”) session on April 2. The legislature considered 3277 measures; 1585 passed and 1692 failed. The legislature also considered amendments to the
Virginia Water Resources Research Center
core  

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

3D‐Printed Dual‐Doped Ag2Se‐Based Thermoelectric Films With Enhanced Thermal Stability

Advanced Materials Technologies, EarlyView.
Sb–Se dual doping enhances the thermal stability of Ag2Se‐based thermoelectric systems. The compositionally tuned nano‐ink is printed into flexible films by direct ink writing (DIW), retaining improved thermoelectric properties after annealing up to 400°C.
Ahasun Habib Hridoy, Nishat Paul, Naimul Arefin, Axel Lopez, Peiran Wei, Brandon Dumars, Yan Chen, Mortaza Saeidi, Minxiang Zeng   +8 more
wiley   +1 more source

High Throughput Aerosol Jet Printing to Operationalize High Aspect Ratio Patterning

Advanced Materials Technologies, EarlyView.
High‐throughput aerosol jet printing poses distinct limiting mechanisms to the printing process. These include rapidly changing ink chemistries, atomization instabilities, and liquid‐phase spreading. The combination of in‐line heating, process monitoring, and traditional optimization procedures enables rapid printing of high‐aspect‐ratio structures ...
Bella I. Guyll, Md Mahdi Ul Ishtiaque, Md Ramjan Ali, Todd A. Kingston, Ethan B. Secor   +4 more
wiley   +1 more source

Biodegradable and Edible Milli‐Fluidic Logic Circuits

Advanced Materials Technologies, EarlyView.
Fully biodegradable and edible fluidic circuits are developed using gelatin‐based valves that operate at low pressure. Logic gates, a one‐bit memory, and a ring oscillator are demonstrated, showing that biodegradable materials can perform computation and control.
Shuhang Zhang, Bokeon Kwak, Özgün Ekrem, Dario Floreano   +3 more
wiley   +1 more source

Recent Advances in Transparent Microelectrode Device Architecture and Fabrication Strategies for Biomedical Applications

Advanced Materials Technologies, EarlyView.
Transparent microelectrode arrays enable simultaneous optical and electrical electrophysiology with high spatiotemporal resolution, allowing multimodal observations of dynamic biological systems. Advances in materials and device architectures improve device performance by addressing key trade‐offs between optical transparency, impedance, and ...
Michael Abraham Listyawan, Tran Bach Dang, Chi Cong Nguyen, Yee Lap Pong, Tianruo Guo, Thanh Nho Do, Hoang‐Phuong Phan   +6 more
wiley   +1 more source

Water in the 2000 Virginia General Assembly

, 2000
The Virginia General Assembly held its 2000 session from January 12 to March 10. Lawmakers considered 3,172 bills and resolutions (compared to 2,735 measures considered in 1999).
Virginia Water Resources Research Center
core  

Programming Actuation in 3D‐Printed Micro‐Architectures via Interfacial Adhesion Control

Advanced Materials Technologies, EarlyView.
A two‐phase meniscus‐guided 3D printing method directly fabricates microscale poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and poly(vinyl alcohol) (PVA) bilayers with in situ programmable interfaces. Modulating the meniscus stretching speed switches the interface between separated and bonded states, which controls the mechanical ...
Xiao Huan, Juhyung Kim, Yujin Park, Shiqi Hu, Jihyuk Yang, Nan Huang, Feipeng Chen, Yu Liu, Sixi Cao, Zhuoran Wang, Ho Cheung Shum, Barbara Pui Chan, Dongwoon Shin, Ji Tae Kim   +13 more
wiley   +1 more source

Angled Nozzle Aerosol Jet Printing to Streamline Conformal Patterning of Electronics

Advanced Materials Technologies, EarlyView.
A modular, angled aerosol jet printhead is demonstrated to streamline patterning on nonplanar surfaces, including 90° step edges and confined internal geometries. A detailed analysis of gravitational settling for a sheathed aerosol flow and deconvolution of oblique deposition and gravitational effects supports the versatility of this approach for ...
Louis O. Morgan, Jeremy D. Rurup, Hal K. Griswold, Md Ramjan Ali, Ethan B. Secor   +4 more
wiley   +1 more source

Processing‐Driven Engineering of Transparent Conductive In‐Zn‐O Thin Films: A Comparative Study of Spin‐Coating, Inkjet Printing, and Screen Printing

Advanced Materials Technologies, EarlyView.
Transparent, electrically conductive In–Zn–O thin films are solution‐processed by spin coating, inkjet printing, and, as demonstrated here for the first time, screen printing. The chosen deposition technique determines the solution composition, which in turn governs the resulting microstructure and optoelectronic performance.
Danjela Kuscer, Izabela Čurković, Brigita Kmet, Aleksander Matavž   +3 more
wiley   +1 more source