Results 41 to 50 of about 74,787 (316)
Experiment on Conical Pick Cutting Rock Material Assisted with Front and Rear Water Jet
Advances in Materials Science and Engineering, 2015 Conical picks are one kind of cutting tools widely used in engineering machinery. In the process of rock breaking, the conical pick bears great cutting force and wear. To solve the problem, a new method, conical pick assisted with high pressure water jet,
Xiaohui Liu +3 more
doaj +1 more source
Numerical and experimental investigation of a confined plunging liquid jet system [PDF]
, 2012 In a confined plunging liquid jet (CPLJ) system, a liquid jet is allowed to fall in a partially submerged narrow downcomer tube. Liquid jet impingement at gas-liquid interface leads to entrainment of gas, which is dispersed down the downcomer tube in to ...
Mishra, A.
core
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Instability of water jet: Aerodynamically induced acoustic and capillary waves
, 2012 High-speed water jet cutting has important industrial applications. To further improve the cutting performance it is critical to understand the theory behind the onset of instability of the jet. In this paper, instability of a water jet flowing out
Broman, Göran, +3 more
core +1 more source
A: Universality in Vortex Formation. B: Evaluation of Mach Wave Radiation Mechanisms in a Supersonic Jet [PDF]
, 2000 In this thesis two distinct features of coherent structures are investigated. In Part I a model for the pinch-off process in vortex ring formation is developed.
Mohseni, Kamran
core +1 more source
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
AIP Advances, 2022 In order to explore the rising and diffusing path of an underwater thermal jet and the temperature variation of each water layer in the typical ocean thermohaline stratified environment, a three-dimensional mass-heat transport model of the thermal jet in
Feiyang Luo +3 more
doaj +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Micromachines, 2021 In this paper, coating removal characteristics of water jet by micro jet flow affected by cleaning parameters is analyzed. Numerical simulation of fluid field calculates the velocity and pressure distribution of a water jet impinging on a rigid wall ...
Dayong Ning +6 more
doaj +1 more source
Erosion by air enhanced plain water jet
, 2023 95107The article describes the fundamental characteristics of a plain waterjet tool enhanced by air. Here, the geometry of the kerfs on the test materials is described in dependence of the air pressure supplied into the injection head.
Schüler, Manuel, Poloprudský, Jakub
core