Results 201 to 210 of about 2,708,251 (409)

Preliminary Table of Solar Spectrum Wavelengths III

, 1895
Henry A. Rowland
openalex   +1 more source

Laser Additive Manufacturing of Oxide‐Dispersion‐Strengthened Steels: A Simulation‐Based Comparison Between Powder Bed Fusion and Direct Energy Deposition

Advanced Engineering Materials, EarlyView.
Controlling the size and distribution of dispersoids is essential for optimizing the performance of oxide‐dispersion‐strengthened steels. This study focuses on nanoparticle dispersion and agglomeration during laser additive manufacturing of Fe20Cr alloy reinforced with ZrO 2 nanoparticles. Utilizing multiphysics phase‐field simulations and nanoparticle
Somnath Bharech, Yangyiwei Yang, Timileyin David Oyedeji, Prasanth Bondi, Mareen Goßling, Bilal Gökce, Bai‐Xiang Xu   +6 more
wiley   +1 more source

Microstructure, Mechanical Properties, and Antibacterial Performance of Novel Fe‐Mn‐Zn Nanocrystalline Alloys Produced by Mechanical Alloying

Advanced Engineering Materials, EarlyView.
This article presents the development of Fe‐Mn‐Zn nanocrystalline alloys (0–9 wt% Zn) by mechanical alloying and subsequently hot pressing. Their microstructure, density, hardness, wear resistance, corrosion behavior, and antibacterial properties are systematically examined.
Ilker Emin Dag, Funda Kilic, Mrutyunjay Panigrahi, Baris Avar   +3 more
wiley   +1 more source

Genetic Relationship Analysis of Genus Nomorhamphus from Lindu Lake, Central Sulawesi and Adaptive Responses to Exposure Different Light Wavelengths

Jurnal Ilmiah Perikanan dan Kelautan
Graphical Abstract Highlight Research • Genus Nomorhamphusfrom three river inlets of Lindu Lake, Central Sulawesi was identified as Nomorhamphus with CO1 gene. • Green wavelength can accelerate growth and maturation.
Riva Hafidah, Dinar Tri Soelistyowati, Agus Oman Sudrajat, Alimuddin   +3 more
doaj  

Wavelengths from thorium-halide lamps

, 1958
William F. Meggers, Robert W. Stanley
openalex   +1 more source

Fractographic Analysis and Fatigue Behavior of Additively Manufactured Ni‐Superalloy Components with Post Processing Heat Treatment and Hot Isostatic Pressing

Advanced Engineering Materials, EarlyView.
A study of mechanical properties and fractography of PBF‐LB/M‐built Inconel 718, performing heat treatments and hot‐isostatic pressing, is presented. Ultimate tensile strength and fatigue behavior are evaluated, examining differences in maximum load behavior, elongation, and regimes of fatigue.
David Sommer, Ben Truetsch, Cemal Esen, Ralf Hellmann   +3 more
wiley   +1 more source

Some accurately measured infrared wavelengths for calibration of grating spectrometers

, 1952
E. K. Plyler, N. M. Gailar, T. A. Wiggins   +2 more
openalex   +1 more source

Scalable Fabrication of Height‐Variable Microstructures with a Revised Wetting Model

Advanced Engineering Materials, EarlyView.
Height‐variable microstructures are fabricated using a scalable CO2 laser machining approach, enabling precise control of wettability through structural gradients. Classical wetting models fail to capture height‐induced effects, necessitating a revised theoretical framework.
Prabuddha De Saram, Nam‐Trung Nguyen, Navid Kashaninejad   +2 more
wiley   +1 more source

A Comparison of Scanning and Two-Wavelength Microspectrophotometry

, 1958
Mortimer L. Mendelsohn, B. M. Richards
openalex   +1 more source

Tribology of ZrC Coatings and Spherical Tips Acquired with Extraordinarily Stiff, Metal Atomic Force Microscopy Probes

Advanced Engineering Materials, EarlyView.
In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk, Marcin Michałowski, Bogdan Warcholiński, Michał Milczarek, Adam Gilewicz   +4 more
wiley   +1 more source