Results 151 to 160 of about 476,480 (304)

Composition and structure of Rosaceae leaf cuticles: insights into crystal formation and secondary alcohol biosynthesis. [PDF]

Ann Bot
Cote C, Jetter R, Rosado A.
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

A fully integrated magnetofluidic system enabled by a wax phase barrier for automated multiplex meat adulteration detection. [PDF]

Microsyst Nanoeng
Zhou T, Li C, Chen D, Wang J, Li N.
europepmc   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

A Molecular Dynamics Investigation of Wax Crystallization in Crude Oil under Varying Pressures, Temperatures, and CO₂ Contents. [PDF]

ACS Omega
Wang T, Ning Y, Shi S, Zhang X, Qin M, Li S, Liu T, Bai S.   +7 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Investigating the Hydrate and Corrosion Inhibition Efficacy of Propargyl Alcohol: Applicable to Flow Assurance in Natural Gas Pipelines

Chem & Bio Engineering
Sadhbhawana Dubey, Varsha Choudhary, Sanat Kumar, Prakashaiah B G, Asheesh Kumar   +4 more
doaj   +1 more source

Experimental performance, exergy, and economic analysis of an oval tubular solar still integrated with nano-enhanced phase change material. [PDF]

Sci Rep
Aly WIA, Tolba MA, Abdelmagied M.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Efficacy and safety of a novel absorbable bone wax as a hemostatic agent for periacetabular osteotomy: a prospective, randomized controlled trial. [PDF]

BMC Musculoskelet Disord
Wu J, Peng J, Xiao F, Zheng X, Zhu H, Liu C, Han X, Chen X.   +7 more
europepmc   +1 more source