Results 121 to 130 of about 203,033 (304)
Nitroxide‐Mediated Photo‐Polymerization: A Swiss Army Knife for Microfluidic Design
Advanced Materials Technologies, EarlyView.This article illustrates the application of NMP2 to the rapid (less than 1 h) photostructuring and sealing of model structures intended for microfluidic applications. Remarkably, the careful design of resin composition allows completing these steps by simply spreading bare monomer (i.e., no added photoinitiator) on top of the bottom layer embedding ...
Carlo Gonzato +5 more
wiley +1 more source
MetalsAn investigation of intergranular corrosion (IGC) sensitization in molten nitrate salts of austenitic stainless steel welds of AISI 304, AISI 304H, and AISI321 produced by GTAW with ER 308L and ER 347 fillers was performed.
Noparat Kanjanaprayut +5 more
doaj +1 more source
The keyhole region in VPPA welds [PDF]
The morphology and properties of the Variable Polarity Plasma Arc (VPPA) weld composite zone are intimately related to the physical processes associated with the keyhole.
Walsh, Daniel W.
core +1 more source
Determination of spot weld quality Patent [PDF]
, 1969 Nondestructive radiographic tests of resistance ...
Kropp, C. J.
core +1 more source
Smart Closed‐Loop Systems in Personalized Healthcare: Advances and Outlook
Advanced Materials Technologies, EarlyView.A smart closed‐loop e‐textile integrates multimodal sensing, onboard processing, wireless communication, and wearable power to enable real‐time physiological/biochemical monitoring and feedback‐controlled therapy. ABSTRACT Smart textiles represent a revolutionary frontier in healthcare, seamlessly blending fabric and advanced technologies to create ...
Safoora Khosravi +12 more
wiley +1 more source
Portable machine welding head automatically controls arc [PDF]
, 1967 Portable weld tool makes weld repairs out-of-station and on the side opposite the original weld. It provides full automatic control of the arc voltage, current, wire feed, and electrode travel speed in all welding attitudes.
Oleksiak, C. E., Robb, M. A.
core +1 more source
Fabric‐Based Wearable Robotic Exoskeleton Gloves: Advancements and Challenges
Advanced Materials Technologies, EarlyView.This review highlights interdisciplinary technological advances in fabric‐based robotic gloves, focusing on progress in design, fabrication, actuation, sensing, control, and power and energy requirements. It also addresses performance testing and validation, including biomechanical, strength, functional, user experience, and durability assessments, to ...
Ayse Feyza Yilmaz +2 more
wiley +1 more source
Fillet Weld Stress Using Finite Element Methods [PDF]
, 1985 Average elastic Von Mises equivalent stresses were calculated along the throat of a single lap fillet weld. The average elastic stresses were compared to initial yield and to plastic instability conditions to modify conventional design formulas is ...
Green, G. W., Lehnhoff, T. F.
core +1 more source
Degradation Mechanisms in PEM Water Electrolysis: Diagnosis and Impact
Advanced Materials Technologies, EarlyView.This review provides an analysis of degradation mechanisms in proton electrolyte membrane water electrolyzers (PEMWE), focusing on all key components. It discusses diagnostic and measurement techniques for evaluating degradation, less‐studied mechanisms, and an expert survey.
Annik Bernhardt +11 more
wiley +1 more source
Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery
Advanced Materials Technologies, EarlyView.Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein +6 more
wiley +1 more source