Results 161 to 170 of about 15,811 (256)

Effect of Friction Stir Welding Parameters on Mechanical Properties and Formability of Pre-Hardened 2219 Aluminum Alloy. [PDF]

Materials (Basel)
Ye X, Meng X, Pang Q, Zhang S.
europepmc   +1 more source

Behavior of a Novel Cyclic Olefin‐Based Hot‐Melt Adhesive in CFRP Adhesive Joints Compared to Conventional Epoxy‐Based Structural Adhesives

Polymer Composites, EarlyView.
Rate‐dependent performance of composite adhesive joints using thermoset and thermoplastic adhesives, in terms of toughness and fatigue behaviour. ABSTRACT A recently developed hot‐melt adhesive (HMA) based on cyclic olefin chemistry, supplied as a transparent, non‐tacky thermoplastic film with a distinctive polymer microstructure, was evaluated in this
Hossein Malekinejad, Ricardo J. C. Carbas, Eduardo A. S. Marques, Lucas F. M. da Silva   +3 more
wiley   +1 more source

Thermoplastic‐Resin Transfer Molding Technology: Development and Challenges Toward Industrialization

Polymer Composites, EarlyView.
Illustration of the key aspects involved in the manufacture of thermoplastic composites by T‐RTM highlighting the relationships between raw materials, resin mixing strategies, polymerization parameters, and processing equipment ranging from laboratory to industrial scale. ABSTRACT Driven by increasingly stringent international environmental regulations,
Filipe P. Martins, Paulo S. Lima, Ricardo Torcato, Laura Santos, J. M. Oliveira   +4 more
wiley   +1 more source

Laser Welding

Welding International, 2003
openaire   +2 more sources

Effects of Preheating on Internal Modification and Welding Strength of Glass by Ultrafast Laser Pulses. [PDF]

Micromachines (Basel)
Hussein R, Lei S.
europepmc   +1 more source

Effect of Nominal Laminate Thickness on Consolidation Quality and Tensile Properties of Compression‐Molded Polyetherketoneketone/Carbon Fiber Composites

Polymer Composites, EarlyView.
Effect of Mold Cavity Thickness on Consolidation Quality and Tensile Strength of CF/PEKK Composites. ABSTRACT Carbon‐fiber‐reinforced thermoplastic composites have attracted growing attention as high‐performance structural materials due to their superior toughness, shorter processing cycles, and recyclability.
Hyunseok Choi, Chan Joo Lee, Chang‐Soo Kang, Dongearn Kim   +3 more
wiley   +1 more source

A misclassification-aware explainable hybrid CNN-vision transformer framework for radiographic weld inspection. [PDF]

Sci Rep
Parmar K, Jain R, Anitha PT, Jayanthi A, Putchanuthala RB, Upreti K, Ayele TB.   +6 more
europepmc   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, EarlyView.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

Multi-Type Weld Defect Detection in Galvanized Sheet MIG Welding Using an Improved YOLOv10 Model. [PDF]

Materials (Basel)
Xiao B, Yang Y, He Y, Ma G.
europepmc   +1 more source