Results 211 to 220 of about 203,033 (304)

Failure Investigation of Alloy 625 Sockolets After Prolonged Service in an Ammonia Cracker Unit

Materials and Corrosion, EarlyView.
The failure of the sockolets was caused by intergranular cracking and fracture. The thick and highly brittle nitrided layer formed intergranular surface cracks, which propagated along grain boundaries into the base alloy substrate due to the presence of brittle Cr‐rich carbides. ABSTRACT Several sockolets of Alloy 625 operating at 540°C in contact with
Kamlesh Chandra, N. Naveen Kumar, Niraj Kumar   +2 more
wiley   +1 more source

Properties and Microstructure Evaluation of Laser-Welded TP347-TP904L High-Alloy, Stainless Steels Joints, Modified with 309L Filler. [PDF]

Materials (Basel)
Danielewski H, Kurp P, Skrzypczyk A, Kozák J, Konopík P, Yao J, Zhang Q, Rzepa S.   +7 more
europepmc   +1 more source

Experimental and Comparative Study of the Corrosion Behavior of Lean Duplex Stainless Steel in Seawater

Materials and Corrosion, EarlyView.
The localized corrosion behavior of lean duplex stainless steel EN 1.4062 is systematically compared with austenitic and higher‐alloyed duplex grades in natural seawater. A clear resistance ranking is established, highlighting EN 1.4062 as a cost‐effective alternative for limited marine exposure.
Mohammad Hassanzadeh, Nicolas Larché, Audrey Allion‐Maurer, Raf Dewil, Barbara Rossi   +4 more
wiley   +1 more source

Laser Power-Dependent Microstructural Evolution and Fracture Mechanisms in Ti80 Titanium Alloy Welds: A Multi-Scale Investigation. [PDF]

Materials (Basel)
Zheng C, Yang Z, Yi G, Zhang L, Zhou X, Yao X.   +5 more
europepmc   +1 more source

Long‐Term Exposure to Air Pollution and Incidence of Parkinson's Disease: A Danish Nationwide Administrative Cohort Study

Movement Disorders, EarlyView.
Abstract Background Long‐term exposure to air pollution has been linked to Parkinson's disease (PD) incidence, yet evidence is mixed, partly because of challenges with PD diagnosis and definition. We examined this association in a nationwide administrative cohort.
Thomas Cole‐Hunter, Sonja Antic, Youn‐Hee Lim, Jiawei Zhang, Laust Hvas Mortensen, Kees de Hoogh, Steffen Loft, George Maria Napolitano, Stéphane Tuffier, Marie Laura Bergmann, Bert Brunekreef, Gerard Hoek, Beate Ritz, Zorana Jovanovic Andersen, Rina So   +14 more
wiley   +1 more source

On the Projection Welding, Seam Welding and Flash Welding

Journal of the Japan Welding Society, 1968
openaire   +2 more sources

Recent Advances in the Laser‐Based Fabrication and Applications of High‐Entropy Alloy Nanoparticles

MetalMat, EarlyView.
This review presents recent advances in the laser‐based fabrication of high‐entropy alloy nanoparticles, focusing on scalable, environmentally friendly, and compositionally tunable synthesis methods. It highlights the critical influence of laser parameters on nanoparticle size, phase, and morphology, enabling tailored properties for applications in ...
Bibek Kumar Singh, Rajesh Rawat, Archana Tiwari, Venugopal Rao Soma, Ajay Tripathi   +4 more
wiley   +1 more source

A Composite Material Repair Structure: For Defect Repair of Branch Pipe Fillet Welds in Oil and Gas Pipelines. [PDF]

Materials (Basel)
Zhao L, Qiao Y, Yin Z, Xie B, Wang B, Zhou J, Chen S, Wang Z, Wang X, Zhang X, Bian X, Zhang X, Wu Y, Wang P.   +13 more
europepmc   +1 more source

A Comparison of Classical Constitutive Models for High‐Entropy Alloy Behavior: Effects of Medium Strain Rates and Temperature on Plastic Flow

Materials Genome Engineering Advances, EarlyView.
Four constitutive models are evaluated for FeCoNiCr and Al0.6FeCoNiCr HEAs under wide temperature and strain‐rate conditions. The predictive capabilities and limitations of each model are then critically assessed, with particular emphasis on strain rate sensitivity, temperature dependence, and physically unrealistic responses at extreme loading ...
Yooseob Song, Daniel Garcia‐Gonzalez, Tomasz Jankowiak, Alexis Rusinek   +3 more
wiley   +1 more source