Results 51 to 60 of about 203,033 (304)
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Marine Environment Effect on Welded Additively Manufactured Stainless Steel AISI 316L
Journal of Marine Science and EngineeringThis experimental study deals with the effect of the natural marine environment in the Adriatic Sea on the properties of the welded additively manufactured stainless steel AISI 316L. The welding of additively manufactured materials is of special interest
Goran Vukelic +2 more
doaj +1 more source
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
Advanced Engineering Materials, EarlyView.This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
The Effect of Welding Positions on the Weldability of X20CrMoV11-1 Steels
Hittite Journal of Science and Engineering, 2018 I n the study, mechanical properties of martensitic steel X20CrMoV11-1 was investigated after being welded using Tungsten Inert Gas GTAW welding method at different weld positions PC and PJ-EN 6947 . The X20CrMoV11-1 steels have been widely used in
Bunyamin Cicek +3 more
doaj +1 more source
Sustainable and Mass Production of Cotton Dyeing with Natural Dye (Weld) in the Textile Industry
Journal of Natural Fibers, 2022 The use of natural dyes in textile fibers goes back an ancient times. These dyes have been used in traditional methods until now. The use of natural dyes has come to importance in the textile industry in recent years.
Recep Karadag
doaj +1 more source
Evaluation of Superplastic Forming and Weld-brazing for Fabrication of Titanium Compression Panels [PDF]
, 1985 The two titanium processing procedures, superplastic forming and weld brazing, are successfully combined to fabricate titanium skin stiffened structural panels. Stiffeners with complex shapes are superplastically formed using simple tooling.
Bales, T. T. +2 more
core +1 more source
Fatigue of friction stir welded 2024-T351 aluminium alloy
, 2002 Fatigue failure characteristics of friction stir welds in 13mm gauge 2024-T351 plate have been assessed. Failure occurred from either the weld region (nugget/flow arm) or from the material immediately surrounding the weld.
Booth, D., Sinclair, I.
core +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Reviews on Advanced Materials Science, 2022 In the present research work, the 2.25Cr1Mo0.25V steel plates with a thickness of 112 mm were welded using the multi-pass submerged automatic arc welding process.
Song Yan +6 more
doaj +1 more source