Results 21 to 30 of about 5,676 (264)
Microstructure Development during Low-Current Resistance Spot Welding of Aluminum to Magnesium
Journal of Manufacturing and Materials Processing, 2019 Resistance spot welding of aluminum (Al5754) to magnesium (AZ31B) alloys results in the formation of a variety of solidification microstructures and intermetallic compounds that may affect the in-service performance of the weld.
Kavian O. Cooke, Tahir I. Khan
doaj +1 more source
eXPRESS Polymer Letters, 2019 In this paper, a kind of polypropylene (PP) foam plastic parts with special weld lines were obtained by core-back foam injection molding with chemical blowing agent. A new kind of weld line was found and its formation process was proposed.
H. Wu +4 more
doaj +1 more source
Journal of Materials Research and Technology, 2020 The solute mixing phenomena of filler and base metal melts during dissimilar-filler metal-inert gas (MIG) welding are simulated by a multi-phase lattice Boltzmann (LB) model for predicting macrosegregation formation in the weld joint.
Qingyu Zhang +7 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 304 austenitic stainless steel with a thickness of 7.5 mm was welded by high-power fiber laser welding. The effects of main welding parameters, including laser power, welding speed, and defocusing amount, on weld formation were studied in detail.
Peikang Tao +3 more
doaj +1 more source
Welding fumes formation. V. Formation of final agglomerates.
Physics of Aerodisperse Systems, 2014 The dusty plasma behavior is studied in the process of coagulation of the primary particles, which are formed as a result of the nucleation and nuclei growth in the condensable hightemperature vapors. The study is concentrated to the example of the thermal plasma formed in the welding fume in the arc welding process where the electrodes covered with ...
V. I. Vishnyakov +3 more
openaire +1 more source
Journal of Materials Research and Technology, 2021 This paper studied lap welding on 1.5 mm AA6061 and AA5182 aluminum alloy sheets with laser beam circular oscillation. The joint form is commonly used in new energy car bodies to achieve the purpose of reducing weight and combining the strength and ...
Lin Chen +3 more
doaj +1 more source
Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution
Advanced Engineering Materials, EarlyView.Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen +3 more
wiley +1 more source
Monitoring of aluminum alloy weld formation using TIG based on passive vision
Hanjie xuebaoDuring the butt-welding process of thin-plate aluminum alloys, the base metal was affected by fluctuations in the joint gap and uneven heating and heat dissipation. As a result, the weld was usually defective. A passive vision sensing method was selected
Shengnan GAI +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source