Results 81 to 90 of about 69,300 (308)
Finite element simulation of magnesium alloys laser beam welding [PDF]
, 2010 The authors are grateful to FONDERIE MESSIER (HONSEL group) that provided the as-cast magnesium alloy workpieces. The authors would like also to acknowledge the technical support of Dr.
BARRALLIER, Laurent +4 more
core +5 more sources
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
Towards Defect Phase Diagrams: From Research Data Management to Automated Workflows
Advanced Engineering Materials, EarlyView.A research data management infrastructure is presented for the systematic integration of heterogeneous experimental and simulation data required for defect phase diagrams. The approach combines openBIS with a companion application for large‐object storage, automated metadata extraction, provenance tracking and federated data access, thereby supporting ...
Khalil Rejiba +5 more
wiley +1 more source
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
Hanjie xuebaoIn order to further improve the quality of aluminum alloy welded joints, the alternating magnetic field-assisted cold metal transfer (CMT) technology was adopted for butt welding of the same 6061 aluminum alloy, and the influence of the magnetic field on
Chen YANG +5 more
doaj +1 more source
Journal of Magnesium and Alloys, 2015 Liquid–solid extrusion directly following vacuum infiltration (LSEVI) is an infiltration–extrusion integrated forming technique, and transverse weld between upper residual magnesium alloy and magnesium matrix composites is a common internal defect, which
Jian Liu +3 more
doaj +1 more source
Effect of beam oscillation on porosity and intermetallics of electron beam welded DP600-steel to Al 5754-alloy [PDF]
, 2019 Formation of porosity and intermetallic compounds (IMCs) were studied in electron beam welded (EBW) DP-600 steel to Al-5754 dissimilar alloy joints at three different weld conditions such as without beam oscillation, with beam oscillation and with ...
Dinda, Soumitra Kumar +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.Cladding is a proven method that boosts the surface qualities of mechanical parts by applying a layer of more durable material over a base substrate. This work responds to the needs of offshore and pressure vessels sectors by focusing on cladding a super austenitic steel onto low‐carbon steel through gas tungsten arc welding.
E. J. da Cruz Junior +6 more
wiley +1 more source
Studies on fatigue behaviour of weld-bonds of Al-Mn-Mg alloy [PDF]
, 2013 In the present paper, fatigue and metallurgical behaviour of weld-bonds and adhesive bonds developed using 2 mm thick aluminium alloys namely 5052 alloy have been reported. Weld-bonds were prepared using structural adhesive (Epoxy resin) and spot welding
Dwivedi, Dheerendra, Mittal, Mayank
core
A model comparison to predict heat transfer during spot GTA welding [PDF]
, 2013 The present work deals with the estimation of the time evolution of the weld fusion boundary. This moving boundary is the result of a spot GTA welding process on a 316L stainless steel disk. The estimation is based on the iterative regularization method.
CARIN, Muriel +2 more
core +5 more sources