Results 161 to 170 of about 2,919 (265)

Research on the Influence Mechanism of Thermal Load on the Au-Sn Sealing Weld State on Three-Dimensional DPC Substrates. [PDF]

Materials (Basel)
Zhao H, Cao L, Wang S, Zhang H, Chen M.
europepmc   +1 more source

Effect of Variations in the Ring Thickness on the Dynamic Performance of the Bimetal Gears

International Journal of Mechanical System Dynamics, EarlyView.
ABSTRACT This study used a six‐degrees‐of‐freedom dynamic model to analyze the dynamic response of bimetal spur gears. Aluminum alloy forms the core of the bimetal gears, and a uniform‐thickness steel ring surrounds the teeth. Gear mesh stiffness of bimetal gears and the transmission error have been assessed using a numerical approach based on finite ...
Bikramjit Singh, Pawan Kumar, S. P. Harsha   +2 more
wiley   +1 more source

Study on Mechanical Properties of Adjustable-Ring-Mode Laser Scanning Welding of TA1 Titanium Alloy to 304 Stainless Steel Dissimilar Thin Sheets. [PDF]

Materials (Basel)
Li G, Yu T, Yang P, Zhao S, Zhang S, Ma H, Wu S, Li J, Gao M.   +8 more
europepmc   +1 more source

Characterization of Fuel Rods Supported by Dimple‐Less Spacer Grids and Subjected to Nonlinear Vibrations

International Journal of Mechanical System Dynamics, EarlyView.
ABSTRACT An experimental campaign was undertaken to demonstrate the applicability of the Bouc–Wen hysteretic model to describe the hysteretic system of the recent Framatome dimple‐less spacer grid design for Pressurized Water Reactors. The experimental setup subjected a reduced‐length fuel rod, supported at both ends by dimple‐less grids, to forced ...
Giovanni Ferrari, Brian Painter, Kostas Karazis, Marco Amabili   +3 more
wiley   +1 more source

Effects of Multi-Pass Butt-Upset Cold Welding on Mechanical Performance of Cu-Mg Alloys. [PDF]

Materials (Basel)
Yuan Y, Pang Y, Xiao Z, Li S, Wang Z.
europepmc   +1 more source

Strain Development During Cure of Partially Pre‐Cured Thermosetting Composites Measured With Distributed Fiber Optic Sensors

Polymer Composites, EarlyView.
Schematic representation of the beneficial effect of ply pre‐curing on temperature overshoot, internal strain and warpage during cure of thin and thick thermosetting composites. ABSTRACT Detection of manufacturing‐induced defects in thermosetting composites is crucial to guarantee part quality, safety, and improve manufacturing efficiency.
Francesco Taddei, Giacomo Struzziero, Valentin Ott, Véronique Michaud   +3 more
wiley   +1 more source

Prediction of Mechanical Properties of Injection-Molded Weld Lines of Glass Fiber-Reinforced Composites. [PDF]

Polymers (Basel)
Bao Z, Yan Y, Zhang Y, Dong R, Han W, Liu Q.   +5 more
europepmc   +1 more source

Effect of Consolidation Time in Hot Press Compression Molding of Continuous Carbon Fiber‐Reinforced Polyetheretherketone Composite

Polymer Composites, EarlyView.
Influence of consolidation time on interlaminar shear strength and void content after hot press consolidation and vacuum bag only processes. ABSTRACT Processing long fiber reinforced thermoplastic composites such as polyaryletherketones with carbon fibers (CF/PEEK) has found interest in the aerospace industry due to short‐time manufacturing and ...
Adrian Korycki, Fabrice Carassus, Christian Garnier, France Chabert, Toufik Djilali   +4 more
wiley   +1 more source

Optimizing Tensile Strength of Low-Carbon Steel Shafts with Stacked Ring Substrates in WAAM Using Taguchi and Random Forest Regression. [PDF]

Materials (Basel)
Nguyen VM, Minh PS, Vo MH.
europepmc   +1 more source