Results 121 to 130 of about 7,004 (249)
Ultra Short Pulse Laser Welding of Glass to Metal in the Low Fluence Regime
Laser &Photonics Reviews, EarlyView.Ultrashortpulse laser welding enables precise joining of glass and metal with minimal thermal damage. We introduce the TwoThresholds Criteria to identify suitable laser parameters by combining the nonlinearabsorption threshold in glass with the metalmodification fluence threshold.
Lukas Günther +4 more
wiley +1 more source
Laser Welding of Titanium/Steel Bimetallic Sheets with In Situ Formation of Fex(CoCrNiMn)Tiy High-Entropy Alloys in Weld Metal. [PDF]
Materials (Basel)Liu D, Ma Z, Xue N, Wang W, Han S.
europepmc +1 more source
Failure Investigation of Alloy 625 Sockolets After Prolonged Service in an Ammonia Cracker Unit
Materials and Corrosion, EarlyView.The failure of the sockolets was caused by intergranular cracking and fracture. The thick and highly brittle nitrided layer formed intergranular surface cracks, which propagated along grain boundaries into the base alloy substrate due to the presence of brittle Cr‐rich carbides. ABSTRACT Several sockolets of Alloy 625 operating at 540°C in contact with
Kamlesh Chandra +2 more
wiley +1 more source
Materials and Corrosion, EarlyView.The localized corrosion behavior of lean duplex stainless steel EN 1.4062 is systematically compared with austenitic and higher‐alloyed duplex grades in natural seawater. A clear resistance ranking is established, highlighting EN 1.4062 as a cost‐effective alternative for limited marine exposure.
Mohammad Hassanzadeh +4 more
wiley +1 more source
Materials and Corrosion, EarlyView.This article examines the impact of externally introduced chromium compounds on the localized corrosion of 316 L stainless steel in acidic chloride environments such as hydrochloric acid. While the corrosion resistance of 316 L relies on the formation of a chromium‐rich passive oxide layer, industrial conditions may expose the steel to various chromium
Florence Lequien
wiley +1 more source
Macromolecular Rapid Communications, EarlyView.Liquid crystal elastomer (LCE) filaments are fabricated through extrusion with in‐process UV curing, enabling controlled flow alignment and network locking of mesogens. The resulting structure responds to thermal or optical stimuli, inducing molecular reorientation and macroscopic contraction.
Anne Schwarz‐Pfeiffer, Shazia Mehtab
wiley +1 more source
Macromolecular Symposia, EarlyView.ABSTRACT This study aims to validate the structural and thermomechanical reliability of an additively manufactured test chamber specifically designed for the experimental investigation of sustainable aviation fuel (SAF) atomization under jet‐in‐crossflow (JICF) conditions representative of gas turbine afterburners. The proposed test chamber is designed
Valerio Acanfora +4 more
wiley +1 more source
Effect of Ni Element in Self-Shielded Flux-Cored Wires on the Microstructural and Mechanical Property Evolutions of X80 Pipeline Steel Girth Welds. [PDF]
Materials (Basel)Jia S, Cui C, Mao C, Liu G, Liu Q.
europepmc +1 more source
Materials Genome Engineering Advances, EarlyView.Four constitutive models are evaluated for FeCoNiCr and Al0.6FeCoNiCr HEAs under wide temperature and strain‐rate conditions. The predictive capabilities and limitations of each model are then critically assessed, with particular emphasis on strain rate sensitivity, temperature dependence, and physically unrealistic responses at extreme loading ...
Yooseob Song +3 more
wiley +1 more source
Polymer Composites, EarlyView.Rate‐dependent performance of composite adhesive joints using thermoset and thermoplastic adhesives, in terms of toughness and fatigue behaviour. ABSTRACT A recently developed hot‐melt adhesive (HMA) based on cyclic olefin chemistry, supplied as a transparent, non‐tacky thermoplastic film with a distinctive polymer microstructure, was evaluated in this
Hossein Malekinejad +3 more
wiley +1 more source