Results 121 to 130 of about 2,407 (262)

Crystallinity, Porosity, and Microstructure of Polyphenylene Sulfide Composite Parts Fabricated by Filament‐Extrusion Additive Manufacturing

Polymer Composites, EarlyView.
High‐performance PPS composites for FFF: formulation and characterization linking microstructure and crystallization to adhesion and mechanical properties. ABSTRACT Polyphenylene sulfide (PPS) was compounded with recycled carbon fibers (rCF) and thermal black (TB) particles, followed by injection molding (IM) and extrusion of the compounded composites ...
Dogan Arslan, Mihaela Mihai, Daniel Therriault, Martin Lévesque   +3 more
wiley   +1 more source

Construction of a CNN-SK weld penetration recognition model based on the Mel spectrum of a CMT arc sound signal. [PDF]

PLoS One
Zheng W, Yang K, Chen J, Huang H, Yang J.   +4 more
europepmc   +1 more source

Behavior of a Novel Cyclic Olefin‐Based Hot‐Melt Adhesive in CFRP Adhesive Joints Compared to Conventional Epoxy‐Based Structural Adhesives

Polymer Composites, EarlyView.
Rate‐dependent performance of composite adhesive joints using thermoset and thermoplastic adhesives, in terms of toughness and fatigue behaviour. ABSTRACT A recently developed hot‐melt adhesive (HMA) based on cyclic olefin chemistry, supplied as a transparent, non‐tacky thermoplastic film with a distinctive polymer microstructure, was evaluated in this
Hossein Malekinejad, Ricardo J. C. Carbas, Eduardo A. S. Marques, Lucas F. M. da Silva   +3 more
wiley   +1 more source

Swing-Arc Narrow-Gap Submerged Arc-Welding Process Assisted by Pre-Embedding Cold Wires. [PDF]

Materials (Basel)
Liu S, Cao Y, Li H, Zhu J, Zhou C, Zhu Z, Wang J.   +6 more
europepmc   +1 more source

Thermoplastic‐Resin Transfer Molding Technology: Development and Challenges Toward Industrialization

Polymer Composites, EarlyView.
Illustration of the key aspects involved in the manufacture of thermoplastic composites by T‐RTM highlighting the relationships between raw materials, resin mixing strategies, polymerization parameters, and processing equipment ranging from laboratory to industrial scale. ABSTRACT Driven by increasingly stringent international environmental regulations,
Filipe P. Martins, Paulo S. Lima, Ricardo Torcato, Laura Santos, J. M. Oliveira   +4 more
wiley   +1 more source

Numerical Investigation on Thermal Fluid Flow-Induced Porosity During EBW of Aluminum Alloy. [PDF]

Materials (Basel)
Zeng R, Song D, Cui H, Wang T.
europepmc   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, EarlyView.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

A misclassification-aware explainable hybrid CNN-vision transformer framework for radiographic weld inspection. [PDF]

Sci Rep
Parmar K, Jain R, Anitha PT, Jayanthi A, Putchanuthala RB, Upreti K, Ayele TB.   +6 more
europepmc   +1 more source

Fusion Bonding Repair of Impact‐Damaged Elium Laminates: Comparison of Hot Pressing and Joule Heating

Polymer Composites, EarlyView.
Joule Heating‐Enabled Repair of Impact‐Damaged GFRP/Elium Laminates. ABSTRACT This study investigates the repairability of glass fiber‐reinforced Elium (GFRP/Elium) laminates incorporating nickel‐coated carbon veils, focusing on hot pressing and Joule heating as fusion bonding repair techniques.
Ozan Can Zehni
wiley   +1 more source

Advancing Defect Detection in Laser Welding: A Machine Learning Approach Based on Spatter Feature Analysis. [PDF]

Sensors (Basel)
Solovev G, Klokov E, Krasnov D, Sokolov M.   +3 more
europepmc   +1 more source