Results 161 to 170 of about 398 (208)

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Mechanical Performance of FDM-Printed PLA Joined by Portable Friction Stir Welding: Influence of Infill Density and Tool Pin Geometry. [PDF]

Polymers (Basel)
Almazán JA, Almazán MÁ, Marín MM, García-Domínguez A, Rubio EM.   +4 more
europepmc   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Simulation Analysis of Thermal Deformation and Extruded Profile Formability of Al-10Mg-3Zn Aluminum Alloy. [PDF]

Materials (Basel)
Niu G, Li W, Jiang K, Yang Y, Wang G, Liu C, Zhuang L.   +6 more
europepmc   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

Wear Behavior of Austenitic Stainless Steel 308L Fabricated by Wire Arc Additive Manufacturing. [PDF]

Materials (Basel)
Alzughaibi S, Alammari Y, Alrumayh A, Alamoudi MT, Alzahrani FJ, Noor HH, Alqosaibi K.   +6 more
europepmc   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Self-Healing Polymer-Based Coatings: Mechanisms and Applications Across Protective and Biofunctional Interfaces. [PDF]

Polymers (Basel)
Cordoba A, Gutiérrez-Mejía FA, Cepeda-Granados G, Cauich-Rodríguez JV, Esquivel Escalante K.   +4 more
europepmc   +1 more source