Results 201 to 210 of about 1,529,417 (286)
Energy Technology, Volume 14, Issue 11, November 2026.A versatile battery module platform houses either high‐energy NMC (155 Ah) or high‐power LTO (23 Ah) lithium‐ion cells for marine hybrid propulsion. Cell‐level failure tests guide the venting design, while a stainless‐steel–ablation hood withstands the up to 580 kW particle‐laden thermal‐runaway jet and aerogel gap fillers block propagation. Both fully
Bernd Steinhoff +3 more
wiley +1 more source
Earthquake Engineering &Structural Dynamics, Volume 55, Issue 14, Page 3540-3560, November 2026.ABSTRACT Rocking podium isolation systems have gained significant research interest as a method of limiting seismic demands on superstructures and eliminating residual post‐earthquake drifts through self‐centring behaviour. However, while numerous models of varying complexity, including analytical, phenomenological, and physical formulations, have been
Marawan Zaki +2 more
wiley +1 more source
Metallurgical Characterization of Welded Joint of Nanostructured Bainite: Regeneration Technique versus Post Welding Heat Treatment. [PDF]
Materials (Basel), 2020 Królicka A +4 more
europepmc +1 more source
Earthquake Engineering &Structural Dynamics, Volume 55, Issue 14, Page 3593-3611, November 2026.ABSTRACT Considering the needs for reducing carbon emissions and except for extreme cases of very degraded existing structures, research on technologies allowing continued use or upgrading of older buildings has become a priority topic. Generally, research on upgrading of reinforced concrete frame structures certainly has a prominent role, because of ...
Francesco Nigro +2 more
wiley +1 more source
Microstructure and Low Cycle Fatigue Properties of AA5083 H111 Friction Stir Welded Joint. [PDF]
Materials (Basel), 2020 Torzewski J +3 more
europepmc +1 more source
Earthquake Spectra, Volume 42, Issue 4, November 2026.Modern confined masonry (CM) construction consists of masonry walls confined by reinforced concrete (RC) tie‐columns and tie‐beams. When built correctly, CM buildings have shown good performance in earthquake's shaking. Even though CM construction has been practised for almost a century in some Latin American countries, its use and standardisation are ...
Ahsana Parammal Vatteri +23 more
wiley +1 more source
Effect of Post-Weld Annealing on Microstructure and Growth Behavior of Copper/Aluminum Friction Stir Welded Joint. [PDF]
Materials (Basel), 2020 Jin Y, Wu B, Lu X, Xing Y, Zhou Z.
europepmc +1 more source
Rare Metals, Volume 45, Issue 11, November 2026.ABSTRACT As the second most widely used metallic material after steel, research on the corrosion resistance of aluminum (Al) alloys holds great significance. To overcome the inherent limitations of experimental methods in capturing long‐term multifactor corrosion behavior of Al alloys, this review summarizes recent advancements in the multiscale ...
Yue Hou +3 more
wiley +1 more source
Rare Metals, Volume 45, Issue 11, November 2026.ABSTRACT To address the insufficient wear resistance of high‐entropy alloy (HEA) coatings under extreme conditions, FeCoNiCrCu and FeCoNiCrCuB0.03Si0.03 microalloyed coatings were fabricated via annular oscillating laser deposition. This work systematically investigated the effects of synergistic B/Si addition on their phase composition, microstructure,
Tao Wang +6 more
wiley +1 more source
Rare Metals, Volume 45, Issue 11, November 2026.ABSTRACT Hot deformation bonding (HDB) offers a promising approach to producing superalloy joints with base‐metal‐level strength, provided that interfacial microstructure is reconstructed through dynamic recrystallization (DRX). Current studies on DRX at bonding interfaces neglect actual phase‐contact configurations, obscuring interfacial DRX ...
Bingchao Xie +6 more
wiley +1 more source