Results 141 to 150 of about 7,270,279 (223)
Materials and Corrosion, EarlyView.Climate‐neutral green hydrogen is produced via water electrolysis using renewable energy. This study explores using cold gas spraying to apply titanium coatings on steel bipolar plates for proton exchange membrane water electrolyzers. The coating shows effective corrosion protection, presenting a promising solution for future designs.
Kirsten Bobzin +3 more
wiley +1 more source
Materials and Corrosion, EarlyView.Multi‐element electrical resistance probes fabricated from industrial carbon steels enable real‐time corrosion monitoring in natural seawater and soil. A micro‐alloyed grade (AMLoCor) demonstrates up to 2.4 times improved uniform corrosion resistance over conventional S355 GP steel.
Erwan Diler, Johan Becker, Thomas Urios
wiley +1 more source
Materials and Corrosion, EarlyView.Hydrogen‐enhanced SCC of WAAM Inconel 625 in 3.5 wt.% NaCl solution. Hydrogen charging reduces passive film stability (lower corrosion potential) and promotes pitting at Laves phase/matrix interfaces. Stress corrosion cracks propagate along Laves‐rich regions, leading to quasi‐cleavage brittle fracture.
Xu Zhang +5 more
wiley +1 more source
Hydrogen Analyses of FSW Cu‐OFP Tested Under Creep Conditions in Sulphide Containing Environment
Materials and Corrosion, EarlyView.Friction stir welded Cu‐OFP exhibits elevated creep rates in sulphide‐containing aqueous environments, with creep increasing as sulphide concentration rises. Hydrogen measurements indicate that sulphide exposure does not increase hydrogen content. ABSTRACT Friction stir welded oxygen‐free phosphorus‐doped copper (FSW Cu‐OFP) is a candidate material for
Patrik Sahiluoma +3 more
wiley +1 more source
Chemically and Mechanically Recyclable Polyolefins Incorporating Covalent Adaptable Networks
Macromolecular Rapid Communications, EarlyView.Low‐molecular‐weight polypropylene is converted into a crosslinked polyolefin containing a covalently adaptable network. The semicrystalline material remains melt‐processable and mechanically recyclable. Its thermal and mechanical properties are comparable to commercial polyolefins.
Andrii Tiiara +4 more
wiley +1 more source
Materialwissenschaft und Werkstofftechnik, EarlyView.The study demonstrated that absorbed energy (Charpy impact test) and fracture toughness (EWF test) are essential for evaluating the mechanical performance of thin sheet metallic materials. Transformation‐induced plasticity (TRIP) steels have been extensively studied concerning their mechanical performance under monotonic loading and conventional ...
W. R. Soares +3 more
wiley +1 more source
MetalMat, EarlyView.Overlap percentage governs the remelting, dilution, and solidification behavior of CMT‐WAAM AISI 308L stainless steel. Increasing overlap to 50% promotes stronger bead‐to‐bead bonding, wider transition zones, and localized hardness enhancement, with the highest hardness observed in the overlap region due to grain refinement and δ‐ferrite redistribution.
Mojtaba Karamimoghadam +4 more
wiley +1 more source
CURRENT WELDING RESEARCH PROBLEMS
Journal of the American Society for Naval Engineers, 1951 openaire +2 more sources
Magnetic Resonance in Medicine, EarlyView.ABSTRACT Purpose To enable MRI‐based nongated 3D depiction of forced expiration with both high spatio‐temporal resolution and fidelity of lung dynamics. Methods An undersampled 3D Fermat looped, orthogonally encoded trajectory (FLORET) was optimized for nonsegmented dynamic acquisitions during forced expiration and a corresponding model‐based ...
Sebastian Scheidel +6 more
wiley +1 more source
Polymer Composites, EarlyView.Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia +4 more
wiley +1 more source