Results 171 to 180 of about 7,270,279 (223)

Tailoring Laser Powder Bed Fusion and Post‐Processing Parameters for JIS SKD61 Tool Steels: Surface Roughness, Microstructure, and Mechanical Properties

steel research international, EarlyView.
Laser powder bed fusion of JIS SKD61 tool steel is systematically optimized using a Taguchi design and ANOVA. Hatch spacing and layer thickness are identified as dominant parameters controlling surface roughness and tensile strength. Subsequent tempering at 600°C improves microstructural stability and mechanical performance, enabling high‐density SKD61
Masrurotin Masrurotin, Andi Ard Maidhah, Maziar Ramezani, Wojciech Macek, Cho‐Pei Jiang   +4 more
wiley   +1 more source

Microstructure Characterization of Bending Effects in 304L Stainless Steel Cladded with Low‐Alloy Steel Weld

steel research international, EarlyView.
Prebending of 304L/Q345R cladded plates significantly alters the subsequent weld thermal cycle and modifies the local interfacial microstructure. Combined electron backscatter diffraction (EBSD) and microscopy analysis demonstrates that deformation twinning, martensitic transformation, and defect initiation are concentrated at the trimaterial junction,
Ali Fahem, Elsiddig Elmukashfi, Hong Dong   +2 more
wiley   +1 more source

Effect of Double Annealing on the Microstructure and Mechanical Properties of a Medium Manganese Steel

steel research international, EarlyView.
A double intercritical annealing strategy is proposed to tailor the multiphase microstructure and mechanical response of a medium‐Mn steel. The treatment produces an ultrafine mixture of ferrite, martensite and multiple austenite populations with graded thermal and mechanical stability, formed through austenite reversion and controlled retransformation.
Mattia Franceschi, Jose A. Jimenez, Carlos Garcia‐Mateo, Radhakanta Rana   +3 more
wiley   +1 more source

Analyses of the Deformability and Chemistry of Non‐Metallic Inclusions in QT Steels With Increased Recycling‐Induced Tramp Element Content

steel research international, EarlyView.
This work uses high‐temperature dilatometry to examine how the tramp elements Cu, Ni, and Sn affect the deformability of non‐metallic inclusions and matrix in quench‐and‐temper steel. Mg‐bearing inclusions deform less than Mg‐free ones. Copper lowers formability. Nickel increases deformability.
Julian Cejka, Isabell Gruber, Gerald Klösch, Susanne Katharina Michelic   +3 more
wiley   +1 more source

Insights Into Paint‐Bake Toughening of Resistance Spot Welds of a 2.0 GPa Warm‐Stamped Medium‐Mn Steel

steel research international, EarlyView.
Paint baking of resistance spot welded joints of 2.0 GPa warm‐stamped medium‐Mn steel activates low‐temperature tempering, forming fine cementite in the fusion zone and enhancing toughness. Crack propagation resistance increases, shifting the failure mode from partial interfacial to complete pullout, with peak load and energy absorption rising ...
Sunusi Marwana Manladan, Savyasachi Nellikode, YeoJin Jang, Sumin Lee, Dileep Chandran Ramachandran, Sung‐bo Heo, Jinyoung Lee, Young‐Kook Lee, Yeong‐Do Park   +8 more
wiley   +1 more source

Crash Behavior of DP800–DP1000 Advanced High‐Strength Steel’s Dissimilar Resistance Spot Welded Joints Under Quasi‐static and High Strain Rates

steel research international, EarlyView.
The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley   +1 more source

Some of the next articles are maybe not open access.

Related searches:

The measurement of spot-welding current

Electrical Engineering, 1940
CURRENT is an essential factor in the complete specification of spot-welding conditions. Therefore, the need for the measurement of spot-welding currents arises, if optimum conditions determined in experimental laboratories are to be duplicated in production shops. Laboratory methods must be accurate and supplemented by facilities for ready calibration
Wendell F. Hess, Robert A. Wyant, Albert Muller   +2 more
openaire   +1 more source

Impact of the Switching Frequency on the Welding Current of a Spot-Welding System

IEEE Transactions on Industrial Electronics, 2017
This paper deals with an analysis of a middle-frequency resistance spot-welding (RSW) system with a dc welding current controlled by a pulsewidth modulated inverter, which supplies a welding transformer with a full-wave rectifier mounted at the secondary.
Robert Brezovnik, Jernej Cernelic, Martin Petrun, Drago Dolinar, Jozef Ritonja   +4 more
openaire   +2 more sources

Current Issues and Problems in Welding Science

Science, 1992
Losses of life and property due to catastrophic failure of structures are often traced to defective welds. However, major advances have taken place in welding science and technology in the last few decades. With the development of new methodologies at the crossroad of basic and applied sciences, the promise of science-based tailoring of composition ...
S A, David, T, Debroy
openaire   +2 more sources

A method of determining the welding current in multispot contact welding

Measurement Techniques, 2010
A method of measuring the welding current on each electrode in bilateral multispot contact welding and of determining its actual values, taking bridging into account, is proposed.
F. Yu. Pkhakadze, M. Sh. Shalamberidze, K. D. Mgaloblishvili, G. G. Dadunashvili   +3 more
openaire   +1 more source