Results 221 to 230 of about 24,703 (309)

Effect of parameters of welding circuit on formation of welding current pulses [PDF]

The Paton Welding Journal, 2016
openaire   +2 more sources

Feasibility of Red Mud Recycling via Hydrogen Plasma Smelting Reduction: Insights From Large‐Scale Laboratory Experiments

steel research international, EarlyView.
Red mud processing in a laboratory hydrogen plasma facility, exceeding one hundred grams of input material, to evaluate the first scale‐up steps for iron recovery. This study demonstrates the feasibility of red mud reduction and the removal of harmful elements.
Daniel Ernst, Jürgen Erich Platl, Daniela Pircher, Magdalena Kirchmair, Lukas Kölbl, Johannes Schenk, Susanne Michelic   +6 more
wiley   +1 more source

Microjoining for biomedical device fabrication: a perspective. [PDF]

Adv Mater Join
Zhang K, Zhou YN, Peng P.
europepmc   +1 more source

Insights Into Paint‐Bake Toughening of Resistance Spot Welds of a 2.0 GPa Warm‐Stamped Medium‐Mn Steel

steel research international, EarlyView.
Paint baking of resistance spot welded joints of 2.0 GPa warm‐stamped medium‐Mn steel activates low‐temperature tempering, forming fine cementite in the fusion zone and enhancing toughness. Crack propagation resistance increases, shifting the failure mode from partial interfacial to complete pullout, with peak load and energy absorption rising ...
Sunusi Marwana Manladan, Savyasachi Nellikode, YeoJin Jang, Sumin Lee, Dileep Chandran Ramachandran, Sung‐bo Heo, Jinyoung Lee, Young‐Kook Lee, Yeong‐Do Park   +8 more
wiley   +1 more source

Computer Modeling of the Ferrite‐To‐Austenite Transformation in a Super‐Duplex Stainless Steel and the Important Role of Trans‐Interface Diffusion

steel research international, EarlyView.
An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén, T. Müller, S. Nouhi, J. Y. Jonsson   +3 more
wiley   +1 more source

Recent Trends in Manufacturing of Thermoplastic Sandwich Structures: A Review. [PDF]

Materials (Basel)
Alliyankal Vijayakumar A, Zahid M, Corvaglia SG, Lionetto F, Maffezzoli A.   +4 more
europepmc   +1 more source

Current Welding Researches in U.S.A.

Journal of the Japan Welding Society, 1967
openaire   +2 more sources

Crash Behavior of DP800–DP1000 Advanced High‐Strength Steel’s Dissimilar Resistance Spot Welded Joints Under Quasi‐static and High Strain Rates

steel research international, EarlyView.
The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley   +1 more source

Welding Current Distribution in the Work-piece and Pool in Arc Welding

Science and Education of the Bauman MSTU, 2015
Alexander Rybachuk, Tsejen Gu
openaire   +1 more source

Performance analysis of strengthening reinforced concrete beams under pure torsion using galvanized steel sheets: Experimental and numerical investigation

Structural Concrete, EarlyView.
Abstract Reinforced concrete (RC) beams can be subjected to torsion, and failure due to torsion is brittle and poses a significant risk to occupants. Moreover, strengthening of existing RC beams in torsion may be required due to the upgrade of the structures or as part of structural rehabilitation.
Ahmed Hamoda, Mizan Ahmed, Ahmad G. Saad, Aref A. Abadel, Saad A. Yehia   +4 more
wiley   +1 more source