Results 131 to 140 of about 2,115 (168)

Hydrogen Analyses of FSW Cu‐OFP Tested Under Creep Conditions in Sulphide Containing Environment

Materials and Corrosion, EarlyView.
Friction stir welded Cu‐OFP exhibits elevated creep rates in sulphide‐containing aqueous environments, with creep increasing as sulphide concentration rises. Hydrogen measurements indicate that sulphide exposure does not increase hydrogen content. ABSTRACT Friction stir welded oxygen‐free phosphorus‐doped copper (FSW Cu‐OFP) is a candidate material for
Patrik Sahiluoma, Tiina Ikäläinen, Juhani Rantala, Timo Saario   +3 more
wiley   +1 more source

Polycarbonate Vitrimers and Dynamic Co‐Networks From Epoxide/Carbon Dioxide Copolymerization

Macromolecular Rapid Communications, EarlyView.
This work demonstrates how CO2‐derived poly(propylene carbonate) and poly(cyclohexene carbonate) backbones influence vitrimer thermo‐mechanical behavior. By tuning backbone composition, epoxide crosslinker chemistry and blend ratios, the crosslinked materials span a wide property window, from highly extensible to stiff, glassy networks, establishing an
Satej S. Joshi, Sophia Aracri, Mark D. Foster, James M. Eagan   +3 more
wiley   +1 more source

Chemically and Mechanically Recyclable Polyolefins Incorporating Covalent Adaptable Networks

Macromolecular Rapid Communications, EarlyView.
Low‐molecular‐weight polypropylene is converted into a crosslinked polyolefin containing a covalently adaptable network. The semicrystalline material remains melt‐processable and mechanically recyclable. Its thermal and mechanical properties are comparable to commercial polyolefins.
Andrii Tiiara, Bernadine Daichendt, Sergiy Minko, Olga Kuksenok, Igor Luzinov   +4 more
wiley   +1 more source

Overlap Percentage Effects on Microstructure and Microhardness in Wire Arc Additive Manufacturing of AISI 308L Stainless Steel

MetalMat, EarlyView.
Overlap percentage governs the remelting, dilution, and solidification behavior of CMT‐WAAM AISI 308L stainless steel. Increasing overlap to 50% promotes stronger bead‐to‐bead bonding, wider transition zones, and localized hardness enhancement, with the highest hardness observed in the overlap region due to grain refinement and δ‐ferrite redistribution.
Mojtaba Karamimoghadam, Mohammad Rezayat, Antonio Mateo, Nicola Contuzzi, Giuseppe Casalino   +4 more
wiley   +1 more source

Additive Manufacturing of Glass Fiber‐Reinforced Polypropylene and Its Behavior Under Controlled Hydrogen Exposure

Polymer Composites, EarlyView.
Experimental and numerical assessment of GFRPP under lower experimental hydrogen pressures using tensile testing, SEM analysis, and hydrogen uptake estimation. ABSTRACT Glass fiber‐reinforced polypropylene (GFRPP) composites are increasingly explored for hydrogen transport and storage due to their lightweight nature and corrosion resistance.
Ahmadyar Qureshi, Ulises Martin, Abdul Mannan, Homero Castaneda   +3 more
wiley   +1 more source

Mechanical and Impact Response of Adhesively Bonded ASA/PA12 Sandwich Structures Produced by Fused Filament Fabrication

Polymer Engineering &Science, EarlyView.
Adhesively bonded ASA/PA12 FFF sandwich structures reveal that interfacial compliance governs mechanical performance. Cyanoacrylate enhances strength but induces brittle failure, while polyurethane improves ductility and impact resistance, demonstrating that adhesive properties and stacking sequence are critical design parameters for optimizing multi ...
Berkay Ergene, Bayram Yildiz, Tolgahan Ermergen, Çağın Bolat   +3 more
wiley   +1 more source

Simulation of the Rotational Molding Process of Polyethylene Using the Smoothed Particle Hydrodynamics Method

Polymer Engineering &Science, EarlyView.
Numerical simulation of polyethylene rotational molding using the Smoothed Particle Hydrodynamics (SPH) method. ABSTRACT This work presents the development of a numerical model based on the smoothed particle hydrodynamics (SPH) method to simulate the rotational molding process of powder thermoplastic polymers, used in the manufacture of liners for high‐
Ali Nourreddine, Albert Lucas, Séverine Boucaud‐Gauchet, Abbas Tcharkhtchi, Sofiane Khelladi   +4 more
wiley   +1 more source

In Situ Atmospheric Plasma Treatment Enables First‐Layer Adhesion of PEEK on Borosilicate Glass for FDM‐Printed Non‐Assembly Mechanisms

Polymer Engineering &Science, EarlyView.
A printhead‐mounted plasma nozzle activates the PEEK melt and the borosilicate print‐bed at the instant of contact. Only this simultaneous in‐situ activation of both interfaces yields reliable first‐layer adhesion (0.22 MPa). ABSTRACT Fused deposition modeling of poly‐ether‐ether‐ketone (PEEK) requires a high‐temperature build plate, yet PEEK does not ...
Paul Sager, Nikolai Schuljak, Arne Bender, Rainer Adelung   +3 more
wiley   +1 more source

Influence of porosity and architecture on the mechanical and acoustic properties of FFF‐printed PLA structures

Polymer International, EarlyView.
The influence of porosity and infill pattern (architecture) on the mechanical and acoustic properties of FFF‐printed PLA is investigated. Ultrasonic analysis highlights the dominant role of interlayer porosity, revealing anisotropic behavior and a transition in elastic properties with increasing porosity.
Makki Ajmi, Simon Bernard, Slim Souissi, Ahmed Elloumi, Pierre Maréchal   +4 more
wiley   +1 more source

Viscoelastic Modeling of Stress Relaxation in Model High‐Performance Covalent Adaptable Networks

Journal of Polymer Science, EarlyView.
Covalent adaptable networks, often referred to as vitrimers, contain a certain fraction of bonds that are able to exchange with other bonds. The ability of this bond exchange to relax stress or result in flow of the material depends on the concentration and specific concentration of these bonds in ways that can be quantified.
Broderick Lewis, Benjamin R. Hafner, Cheol Park, Joseph M. Dennis, Kenneth R. Shull   +4 more
wiley   +1 more source