Results 111 to 120 of about 6,382 (265)

Modelling and Simulation of GMA Welding Process and Welding Power Sources [PDF]

SNE Simulation Notes Europe, 2016
openaire   +1 more source

A Comparison of Classical Constitutive Models for High‐Entropy Alloy Behavior: Effects of Medium Strain Rates and Temperature on Plastic Flow

Materials Genome Engineering Advances, EarlyView.
Four constitutive models are evaluated for FeCoNiCr and Al0.6FeCoNiCr HEAs under wide temperature and strain‐rate conditions. The predictive capabilities and limitations of each model are then critically assessed, with particular emphasis on strain rate sensitivity, temperature dependence, and physically unrealistic responses at extreme loading ...
Yooseob Song, Daniel Garcia‐Gonzalez, Tomasz Jankowiak, Alexis Rusinek   +3 more
wiley   +1 more source

Image‐Derived Volumetry During Forced Expiration Using a 3D Fermat Looped, Orthogonally Encoded Trajectory

Magnetic Resonance in Medicine, EarlyView.
ABSTRACT Purpose To enable MRI‐based nongated 3D depiction of forced expiration with both high spatio‐temporal resolution and fidelity of lung dynamics. Methods An undersampled 3D Fermat looped, orthogonally encoded trajectory (FLORET) was optimized for nonsegmented dynamic acquisitions during forced expiration and a corresponding model‐based ...
Sebastian Scheidel, Viktor Hartung, Matthias Stephan Anders, Corona Metz, Herbert Köstler, Simon Veldhoen, Tobias Wech   +6 more
wiley   +1 more source

Detecting Loosening of Bolt‐Flanged Pipe Using Smoothed Pseudo Wigner–Ville Distribution: Digital Twin‐Based Approach Using Convolution Neural Networks

International Journal of Mechanical System Dynamics, EarlyView.
ABSTRACT In this paper, an integrated digital twin‐based fault‐diagnosis framework is proposed to detect bolt loosening in flanged pipe connections. The approach combines finite element‐based numerical modeling, experimental modal analysis, and advanced signal processing‐assisted deep learning to achieve reliable loosening detection under operational ...
Milad Shabani Yousefabad, Behzad Totakhaneh Bonab, Morteza Homayoun Sadeghi, Mir Mohammad Ettefagh, Mohammad Reza Chalak Qazani   +4 more
wiley   +1 more source

Thermoplastic‐Resin Transfer Molding Technology: Development and Challenges Toward Industrialization

Polymer Composites, EarlyView.
Illustration of the key aspects involved in the manufacture of thermoplastic composites by T‐RTM highlighting the relationships between raw materials, resin mixing strategies, polymerization parameters, and processing equipment ranging from laboratory to industrial scale. ABSTRACT Driven by increasingly stringent international environmental regulations,
Filipe P. Martins, Paulo S. Lima, Ricardo Torcato, Laura Santos, J. M. Oliveira   +4 more
wiley   +1 more source

Analysis of the Interfacial Bond Strength in Overmoulded Thermoplastic Composites

Polymer Composites, EarlyView.
Two‐step injection overmoulding process investigated in this work, showing selective gate injection over a 450 mm demonstrator beam to vary flow length and rib pull‐off mechanical testing with fractographic characterisation of the overmoulded interface.
Casilda S. Villalobos, Samson Gnanadass, Jaipal Gupta, Neill Raath, Neil Reynolds, Ton Peijs   +5 more
wiley   +1 more source

Effect of Accelerated Aging on the Performances of 3D Printed Polylactic Acid‐Polyhydroxyalkanoate Specimens

Polymer Engineering &Science, EarlyView.
The accelerated aging behaviours on the FFF‐fabricated PLA‐PHA Specimens. ABSTRACT Despite the increasing use of biodegradable polymers in additive manufacturing, their long‐term durability remains insufficiently understood. The aim of this study to investigate the influence of accelerated aging on the performance of fused filament fabrication‐printed ...
Han Xu, Jiayu Chen, Yinshi Lu, Handai Liu, Farnoosh McDonagh, Evert Fuenmayor, Ian Major, Genfu Xiao, Ke Gong   +8 more
wiley   +1 more source

In Situ Atmospheric Plasma Treatment Enables First‐Layer Adhesion of PEEK on Borosilicate Glass for FDM‐Printed Non‐Assembly Mechanisms

Polymer Engineering &Science, EarlyView.
A printhead‐mounted plasma nozzle activates the PEEK melt and the borosilicate print‐bed at the instant of contact. Only this simultaneous in‐situ activation of both interfaces yields reliable first‐layer adhesion (0.22 MPa). ABSTRACT Fused deposition modeling of poly‐ether‐ether‐ketone (PEEK) requires a high‐temperature build plate, yet PEEK does not ...
Paul Sager, Nikolai Schuljak, Arne Bender, Rainer Adelung   +3 more
wiley   +1 more source

Atomistic insight into Al-Mg friction stir welding process via molecular dynamics simulation. [PDF]

PLoS One
Nguyen VT, Hoang VH, Nguyen TT, Thien TN, Vo XT, Nguyen VTT.   +5 more
europepmc   +1 more source

Numerical simulation of weld pool in GMA welding

Preprints of the National Meeting of JWS, 2009
Yamane, Satoshi, Kaneta, Tomoaki, Yamamoto, Hikaru, Nakajima, Toru, Oshima, Kenji   +4 more
openaire   +1 more source