Results 41 to 50 of about 206,831 (305)
Advanced Engineering Materials, EarlyView.Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley +1 more source
The emerging of employment gap in the Malaysian construction industry [PDF]
, 2018 Employment of young people is a big issue in the Malaysian construction industry. This is a common phenomenon not only in Malaysia but affected most developed and developing countries around the world.
A Halim, Hazruwani +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen +3 more
wiley +1 more source
Robot-sensor synchronization for real-time seamtracking in robotic laser welding [PDF]
, 2005 The accuracy requirements of laser welding put high demands on the manipulator that is used. To use industrial six-axis robots for manipulating the laser welding optics, sensors measuring the seam trajectory close to the focal spot are required to meet ...
Aarts, R.G.K.M. +3 more
core +3 more sources
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
Welding Characteristic Analysis of Hybrid Welding on 2014 Aluminum Alloy
International Journal of Electrochemical Science, 2013 The experiment of TIG arc and laser high-frequency pulse TIG hybrid welding for 2014 aluminum alloy with the thickness of 7mm were carried out. Through the two welding processes experiments, the correlation between welding process and joints structure as
Zongyu Gao +4 more
doaj +1 more source
Materials & Design, 2020 Carbon fiber reinforced plastic (CFRP) is a prospective lightweight material in automobile industry. However, joining metal and CFRP is a great challenge.
Sendong Ren +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Analisa Metalografi Pengaruh Filler Serbuk Zinc Mesh 200 Dengan Berat 0,07 Gr Dan 0,08 Gr Pada Las Titik Alumunium Dan Stainless Steel [PDF]
, 2018 As the time progressed, the development of welding technology is going forward, one of them is spot welding. The purpose of this research to understand the zinc filler’s weight effect in dissimilar material welding between aluminium and stainless steel ...
, M.Alfatih Hendrawan, S.T, M.T +1 more
core
Multi-physics simulation of friction stir welding process [PDF]
, 2009 Purpose: The Friction Stir Welding (FSW) process comprises of several highly coupled (and non-linear) physical phenomena: large plastic deformation, material flow transportation, mechanical stirring of the tool, tool-workpiece surface interaction ...
Hamilton, R., Li, Hongjun, Mackenzie, D.
core +1 more source