Results 211 to 220 of about 828,080 (265)

Deep Gas Well Completion Practices

SPE Deep Drilling and Production Symposium, 1972
This paper was prepared for the International Deep Drilling Symposium of the Society of Petroleum Engineers of AIME, to be held in Amarillo, Tex., Sept. 11–12, 1972. Permission to copy is restricted to an abstract of not more than 300 words. Illustrations may not be copied. The abstract should contain conspicuous acknowledgment of where and by whom the
openaire   +1 more source

Well Cementing and Completion

2020
This chapter mainly introduces casing program design, casing strength design, cementing technologies, and well completion technologies. Casing program is the basis of drilling engineering which is to determine the casing levels, setting depth, top of cement, match of casing sizes, and hole section sizes. Casing strength design is mainly composed of the
Zhichuan Guan, Tinggen Chen, Hualin Liao
openaire   +1 more source

Permanent-Type Well Completion

Journal of Petroleum Technology, 1953
Abstract Very encouraging progress has been made in the development of the permanent-type well completion which decreases considerably the cost of completions and workovers and aids in the acquisition of reliable reservoir information at low cost.
T.A. Huber, G.H. Tausch
openaire   +1 more source

EVALUATION OF GAS STORAGE WELL COMPLETIONS WITH WELL LOGS

Proceedings of Fall Meeting of the Society of Petroleum Engineers of AIME, 1970
This paper was prepared for the 45th Annual Fall Meeting of the Society of Petroleum Engineers of AIME, to be held in Houston, Tex., Oct. 4–7, 1970. Permission to copy is restricted to an abstract of not more than 300 words. Illustrations may not be copied.
B.A. Smith, M.R. Neal
openaire   +1 more source

Lubricants Enabled Completion of ERD Well

SPE/IADC Drilling Conference, 2007
Abstract Lubricants are often added to the completion or drilling fluid, in order to reduce friction between tubular equipment run into the well, and the wall of the well. This paper shows in detail how the addition of a lubricant to an oil based drilling fluid affected the lubricity significantly in the second of two comparable drill ...
Jonny Holand, Svein Kvamme, Tor Henry Omland, Arild Saasen, Knut Taugbol, John Jamth   +5 more
openaire   +1 more source

Drilling and Completing a Well

2020
Drilling an oil well safely, efficiently, accurately and to target is one of the great engineering achievements of the late twentieth century. In this chapter we will begin with an overview of the methods used to drill a well. We will then focus on the different types of drill bits available today as well as the drilling fluid, usually referred to as ...
openaire   +1 more source

A New Well-completion Technique

Transactions of the AIME, 1947
Abstract Completion and production data presented for three wells in the Oakville areaof Live Oak County, Texas, which were completed near the gas-oil or water-oilcontact, indicate that coning may not be as prevalent a cause of failure insuch cases as is commonly assumed.
openaire   +1 more source

Global Cancer Statistics 2020: GLOBOCAN Estimates of Incidence and Mortality Worldwide for 36 Cancers in 185 Countries

Ca-A Cancer Journal for Clinicians, 2021
Hyuna Sung, Jacques Ferlay, Rebecca L Siegel   +2 more
exaly  

Developments in Well Completion Techniques

Fall Meeting of the Society of Petroleum Engineers of AIME, 1957
Abstract Field experiments indicate that well stimulation efficiency can be increased by engineering the completion process as an interrelated series of steps. These steps can be selected in a manner tat will create conditions most conducive to successful stimulation.
openaire   +1 more source

Cancer treatment and survivorship statistics, 2022

Ca-A Cancer Journal for Clinicians, 2022
Kimberly D Miller, Leticia M Nogueira, Angela B Mariotto   +2 more
exaly